Re: HDL descriptions of AD9467FMC reference design
Yes i didn't modify the board, i am using external Sine wave with 100 MHz but now i want to order 250 MHz for full scale operation.I dont know the specification of temperature of soldering on board etc...
View ArticleRe: "E" model scrypt style of spice file for ADG508F
Hi Sofy, This model will work in NI Multisim as it is included in the Analog Devices version of Multisim Component Evaluator 13. Eric.
View ArticleRe: Switching in between my output signals?
Hi, It will depend on what power supplies you have available and the switch configuration that you need. But looking at the bandwidth you have quoted I think you should consider the ADG1208....
View ArticleRe: BF592 hardware use case discuss.
Hi Henry, 1] Blackfin SPI module do not supprt 3-wire protocol. There are separate MISO and MOSI lines for data transfer. But I guess, you can try to implement some part of it by connecting MISO &...
View ArticleRe: No OS ZC702 problem with _XPARAMETERS_PS_H_
Hi Dragos, I did not export the design from the same version of XPS. I didnt export it from any version of XPS. (Is there a user guide describing the procedures and versions of tools to do so?). From...
View ArticleRe: mirrored video output in ADSPBF561
Hi Asma, I guess your video source is interlaced. That is why you are seeing two frames in single frame buffer. Though I feel there is some sync issue between source and processor. There are some...
View ArticleRe: Early termination of SPI using burst mode reads in an ADIS16364
We appreciate you offering this to us. In past inquiries, we have discouraged this practice but since I had not tested this approach personally, I was hesitant to offer the same level of conviction....
View ArticleRe: updating the SD-card - re-submitted
Robin, I tried another computer (Windows) for creating the SD-card and it fails in a similar way: the process of "physdiskwrite" stops after just a couple of minutes with an error message (the error is...
View ArticleRe: Help to clarify the SPI slave description about the SPI_TWC on bf609 HRM
Hi Dell, Yes..info on p1531 is correct: the counters should not be enabled when SPI is configured as slave (although there is no hardware restriction). The info on p1518 needs to be modified. What kind...
View ArticleRe: cf_adv7511_zed - "axi_hdmi_tx_v1_00_a was not found - please see console...
Sorry for the delay, for some reason we did not get an email about this question. Did you make any progress so far? Do you still have the same issue? I already forwarded this question to someone who...
View ArticleRe: AD-FMCOMMS2-EB and ZC702 Board
Did you post this question somewhere else? Are you still looking for an answer? Charly
View ArticleClik here to view.
How to deal with these two errors in CCES?
Hi everyone, I have built an application for 21488 by imitating the sigma studio application for 21489.The modification I take is to correct the “ldf” file to fit with the 3Mbit on chip ram of...
View ArticleADV7511 in board, how to change the channel of I2C bridge
We select different I2C channel in our board with KC705 development board. I changed the I2C ouput in i2c_axi.c( note: Qlf ) and add i2c_axi.c and i2c_axi.h in \\SDK_Workspace\sw\src. And I add...
View Articlewhy I can't use Project Wizard to create correct "LwIP Ethernet application"?
hi guys,i need to write a LwIP Ethernet application on ADSP-BF561 EZ-KIT Lite Evaluation System Rev1.3 and Blackfin USB-LAN EZ-Extender Rev1.2. IDDE is VisualDSP 5.1.When i run the example in...
View ArticleModify+Rebuild reference design of AD9739A
Hello all, I am rebuilding the system.bit file from XPS and when I program the FPGA in SDK and I run it, I get an error(attached). I am using 14.4 version.The default bitstream is generated using 14.1?...
View ArticleRe: Arduino UNO & ADXL362 problem
Hi Gsterken, To get the valid acceleration from the ADXL362, you need to enable it firstly by writing 0x02 to register 0x2D (POWER_CTL). I would suggest you to read DEVID_AD, DEVID_MST, PARTID firstly...
View ArticleRe: AD5933 and AD5934 evaluation board software commands
Thanks a lot for this post. I am trying to access AD5933 under Linux using EVAL-AD5933EBZ, would you please tell me the equivalent of Vendor_Request function in cyusb lib, please the same example of...
View ArticleRe: Distorted color in HDMI transmission
No, we don't have the evaluation board. I am attaching a block diagram of our project for better understanding. The script I am using for ADV7612 is "6-1f" from the default scripts of Analog Devices....
View ArticleClik here to view.
ADV7180->480i->ADV8003 odd-even field issue
Continue below customer's issue, http://ez.analog.com/thread/42117, I have come to field to check the issue. Basic connection is ADV7180->480i=>ADV8003=>SD encoder=>LCD display and TTL...
View ArticleRe: How do you synchronize conversions from 2 AD7799 converters
Thanks for all the answers. I have tested the idea of writing to the registers of both at the same time to set mode and start conversion followed by individual data reads. With the ADCs sampling at...
View Article