Clik here to view.
Re: Oscillation at the output of AD8220
Hi Emman,About this problem Can you give me some advice?URL:https://ez.analog.com/message/147204#147204It really makes me confused for a long timethank you so much!best reagrdszhu
View ArticleADV7625 OSD Character color change
Hi all, I had used the ADV7625 Demo Board to test.When RX port disconnect any HDMI source,and output the OSD menu,you can see the Character color is correct.But when Current input port connect...
View ArticleRe: Error AT AD-FMCOMMS1-EBZ QUICK START GUIDE
hi sweety,thanks for the reply.are u sending the data to dac using DDR(dac_dma_setup) or DDS(dds_setup)?if u can provide ur phone number so that i can directly talk to u .becoz i'm having some problem...
View ArticleSMPSU on 1446
Hello, i've developed a multi-dsp board and it is running fine.The point is that the 1.8V transistor used for core voltage regulation, is getting quite hot.I've used a SOT223 device for each DSP, it is...
View ArticleRe: axi-dmac cyclic transfer + end of transfer interrupt question
Hi, Yes this is correct, since the transfer never ends in cyclic mode no end-of-transfer interrupt will be generated. If you want to get a interrupt after a certain amount of bytes have been transfered...
View ArticleADAU1452 - Delay Block and Loudness Block
Dear Sir/Madam, Is ADAU1452 able to support the following? Allow delay block to use DM0 which able to give customer more than 700mSec total delay (datasheet says AUAU1452 is able to provide 800mSec...
View ArticleRe: ADV7625 OSD Character color change
Hi yeguiyou, We will check this. Could you please let us know what is the Software driver version that you have been using? Best Regards,Jeyasudha.M
View ArticleRe: Error AT AD-FMCOMMS1-EBZ QUICK START GUIDE
Hi Git , I wan feed the i,q samples to RF processing to transmit the data in the ISM band to build a Prototype of Communication System. I didn't send any data to didn't right now ....
View ArticleClik here to view.
Re: Error AT AD-FMCOMMS1-EBZ QUICK START GUIDE
hi sweety, there r two ways to send iq samples to dac ,one is through dds(in which only sine and cosine wave can be given as i and q ) and other is the custom iq data through the ddr . for the second...
View ArticleRe: ADuCM320 Eval.Board CD update
the tool or driver from segger seems not be in the package? thanks. Bruce
View ArticleRe: ADuC836
Yes you can use the 2kByte RAM on-chip for data as you think by declaring it as xdata.
View ArticleProblem in communicating ADuC7020 with LM75A temperature sensor via I2C
Hello,I am using ADuC7020 evaluation board.I have additionally placed two LM75AIM temperature sensor ICs using 10K pull-up resistors.I am trying to communicate using I2C to the sensors and read the...
View ArticleMarking Code
Hello, EngineerZone Users!I've got the following question. I've got a part with the following marking: on top of it - H 1B(maybe 8?) and the Analog Devices symbol; on the bottom side it's written G241...
View ArticleWill AD5934 have a problem if SCL & SDA are pull-up during power reset
Have to provide a power reset capability for the AD5934, will it cause a problem if SCL and SDA pins have 3.3VDC applied via a 4.99k ohm pull-up resistor when the AD5934 power is off?
View ArticleRe: Re: endurance figure Flash/EE memory in Aduc7060
You can erase each page only 10000 times.If you write only one word into that page, than this is not efficient.Better to write into this page multiple data words till it us used completely and than...
View ArticleUse of I2CxCCNT register in ADuC7xxx
hello,I have gone through the AN-895 APPLICATION NOTE explaining I2C, still I'm not able to get a clear picture on the use of I2CxCCNT register.How to know what value to be assigned into it?The...
View ArticleRe: AD8232 heart monitor configuration circuit without electrical signal output
Hi ssunny, The AD8232 is a very sensitive device so any noise can be picked up easily and amplified. You should first try to find out where the noise is getting picked up. You could first try applying...
View ArticleRe: how to define the handler for nested interrupt in CCES ?
hi Kenny: i will try it on the bf609 ezboard. is it possible to choose a nested or not interrupt by the APIs? BRDell
View Article