Re: AD5934 based Conductivity Measurement
Hi sum6666: For the lower side of concentration calibration please enter the right offset value in probe corrections box on the CN0349 software. This is the item 9 at CN0349 Software User Guide...
View ArticleRe: AD5934 based Conductivity Measurement
Hi sum6666 When working with the AD5933 at 1MHz, I was seeing considerable errors in my reading. Have you looked at what the signal looks like on the RFB ( Pin 4). My issues was solved by using a LPF...
View ArticleAD5933 Time taken for measurement
Hi I'm using the AD5933 Eval board to measure capacitances in the range 100pF to 2000pf, with MCLK = 1MHz and sampling frequency at fixed at 1KHz. The Eval board takes considerably longer to do a...
View ArticleAD9234-1000EBZ and ADS7-v2ebz REV C dont work
Hi everyone!I bought a AD9234-1000EBZ and ADS7-V2EBZ REV C for test ADC chip. But i connect two board together and turn on power from ADS7-V2EBZ REV C. and LED 3.3Vin, 12Vin on AD9234 dont light. I...
View ArticleADPD105: Band-Pass Filter configuration
Hi is there any way to change the ADPD105 Band-Pass Filter configuration (change corner frequencies)?
View ArticleClik here to view.
I'm not sure if this is the right place for this,but I can't find one of...
This is for a Hameg HM303-4 Oscilloscope on the "YP" board.It's IC401 AD42830 as seen on the snippet of the schematic below. Can anyone tell me where I can get one? Analog Devices has "0"...
View ArticleClik here to view.
Re: AD9234-1000EBZ and ADS7-v2ebz REV C dont work
Hi,Have you programmed the FPGA? The FPGA needs to be programmed in order to have the power fed to the AD9234 eval board. Please see wiki user guide for more informationEVALUATING THE...
View ArticleRe: fmcomms5+libiio+matlab: limit on continious sampling?
hi again Travis,AD's gnuRadio page you linked to, does not say whether or not it supports fmcomms5.. and also not the gnuRadio wiki. Any direction on that?thanks, baroch
View ArticleRe: ADV7511 / ADV7513 DRM driver with imx7d not probing
Hi Lars, Many thanks for taking the time to reply. Since my original post I have managed to get the ADV7511 probed on boot by enabling 'eudev' device management (previously I was using 'mdev') , but...
View ArticleRe: VCC power supply for ADM3053
Hi lijie, The ADM3053 has two separate supply pins, VCC and VIO. The VIO pin supplies the signal isolation. The VIO pin can be powered with either 3.3V or 5.0V. The signal logic levels will scale with...
View ArticleRe: AD HDL JESD204 Rx
I reviewed results further and it semms, that scrambler work fine, but your core hasprobably problem with lane skew.
View ArticleRe: Capturing Impact Events of ADXL372
As I mentioned earlier, in order to get the max peak data out, you need enable both activity and inactivity interrupts. It looks like you only set the activity interrupt for X-Axis in your code. In...
View ArticleRe: AD5934 based Conductivity Measurement
At 2 kHz excitation with 1 MHz MCLK there are only about 31 step (1 MHz / 16 / 2 kHz = 31.25) per period of your digitally synthesized excitation - not particularly smooth and accurate sinewave to...
View ArticleAD7761 Synchronization
Hey everyone, Just need to check a few things. How exactly is the AD7761 Synchronization done between multiple devices in a daisy chain. Does it matter if the clock arrives at different times to each...
View ArticleRe: AD5934 based Conductivity Measurement
leviathan 's suggestion is a sound one - whatever you see with a scope (if you have access to one) on RFB pin is what is digitized by the on-chip ADC, so the quality of signal there should be pretty...
View ArticleClik here to view.
Re: How optimize volume .metadata folder during development process?
Hi ACH, The .metadata folder is where your CrossCore Embedded Studio (CCES) preferences and intermediate files created by Eclipse plugins, for example, are stored. The .metadata folder your CCES...
View ArticleRe: How we can use no OS api driver for ad9361?
Hi,Travis I build basic project from your no os setup link in sdk of ''hello word'' but how i can edit main c file of DragosB source code for building some applications.One more question is that how i...
View ArticleRe: AD9371 with ZCU102 board - AD9528_initialize() failed
Thank you for the reply . I will try to compile the latest version of hdl . BUT will it effects the config part of AD9528 ?
View ArticleAfter the 12.5MHz clock is added to the ADD9224 clock pin, there is a burr at...
When the AD9224's clock pin is disconnected, the burr of the input port will disappear.
View ArticleClik here to view.
Re: AD9234-1000EBZ and ADS7-v2ebz REV C dont work
Thanks for your reply!But i dont known, how to program code for FPGA.Step 1: I open SPIcontroller software and a notification show "The FPGA needs to be programmed on ADS7V2 platform for SPI...
View Article