Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Re: About AD7740 question

Hello, The on chip reference is 2.5V typ but can vary from 2.3V to 2.7V. The device also has an offset of 7mV typ, 35 mV max and a gain error of 0.1% of span typ, 0.7% of span max. So, there will be...

View Article


Re: Preamplifier (impedance matching) for EVAL-AD7357EDZ

HI Dimitrios, I'm glad it helped. Just let us know if you need anything else. Good luck to your project! Best regards,Emman

View Article


Re: ADV7181c

i checked both the devices i am little bit confused with parameters which all i need to look at, can you guide me with this. any reference ckt is available?.   For AD8145 can i supply VS+ with 5V and...

View Article

Re: ADV7612 and ADV7513 Programming for HDCP

Hi Raja, There are none for ADV7612-- TX is what sets encryption.  On the ADV7513, it's just a matter of turning on encryption. This is discussed in section 4.6 of the programmers guide for ADV7513....

View Article

Re: Audio deembedding in ADV7619 in 4K resolution

Hello Naftali, Yep-- as long as the input data is within the bandwidth of the part (3Ghz HDMI), it can extract the audio. Dave

View Article


Re: RGB Receiver

Hi Mani, That might work to produce single ended inputs that could go into a decoder but I'm not really an expert on that part so I'll ask one to come comment. Dave

View Article

Re: ADV7625SMZ Eye-diagram fail for TXB

Hi Steven, What color space was the customer using when they did this HDMI compliance testing on EVAL-ADV7625-SMZ? -Matt

View Article

Re: RGB Receiver

Hi dave , Yes please we have very sort time to evaluate .  please provide any reference circuit if available.

View Article


Re: AD8512 Half-Wave and Full-Wave Rectifiers

Hi Yuri, I'm still figuring out what should cause the change in the output voltage level.Maybe r.daemon is right but it should came out as what is shown on the data sheet. I'll get back to you soon....

View Article


ADXL362 Unexpected Interrupt

Hi,I'm trying to use the adxl362 to wakeup on an event, take data for a specified amount of time and the return to sleep.  For the most part this works but I get an unexpected activity interrupt...

View Article

Image may be NSFW.
Clik here to view.

Re: FIT rate for ADuM3400

Hello Kaos, The ADuM340x has two transceiver die which are fabricated in 0.6um CMOS process. The transformer die is the second FIT rate you see reported as "None" process.  DaveC

View Article

ADC to KC705 board

I am trying to figure out what would be a good Analog to Digital Converter to use with a KC705.  I have two input signals a clock and a serial line.  The signal is sent at 20 Mhz.  The KC 705 board...

View Article

Can the ADZS-HPUSB-ICE be used to connect to the BF70x family and the BF707...

Hi, I started a new design with the BF706 and would like to use my 'old' JTAG emulator for debugging.Looking in the datasheet of the BF70x and the manual of the BF707 Evalboard I saw that the EMU Pin...

View Article


Re: ADC to KC705 board

I would like to also mention that the signal is -5V to 0V

View Article

Re: ice-100b bfin-gdbproxy bfin-elf-gdb debug problem

i have checkout you repository, configured and built urjtag, but i am still having the same issue ------------------------------------------------jtag> cable probeFound USB cable: ICE-100BICE-100B...

View Article


Re: my endpoint is not acting immediately on CP commands

What is the maximum size of the queue in the Router for storing the downstream messages ?does it work like a FIFO or a LIFO as the last command could be the most relevant one ?Since AdRadioNET uses...

View Article

Re: ADIS16480 X_DELTVEL_OUT Linear Velocity measurements

Hi, yes,I agree on that it should be different on the z axis, but the numbers matched down to the 4th digit after the dot. The new sensor will be a  Xsens MTi-30. Thank you, Rapha

View Article


Re: ADIS16480 Position tracking Problem

The tracking is meant to enhance a mechanically scanning sonar. So accuracy around +-5cm over 0.5s.

View Article

Re: Question related to ADV7842 initialization

Hi Aram, Have you purchased our ADV7842 evaluation board (EVAL-ADV7842-7511)? -Matt

View Article

Re: 1701 Oscillator start problem

Hi Gordon,  Thank you for your observation. Bob

View Article
Browsing all 28044 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>