ADAU1461 Botting
Dears can you give examples about micro-controllers that cheap and can boot ADAU1461 Regards
View ArticleSplit Screen observed while capturing PAL M using ADV7181C
Hi,I am facing split screen issue in the captured video, when my input resolution is PAL M. (Composite video standard Used in Brazil).I am using ADv7181C chip. To brief about this issue: I was...
View ArticleRe: ADV7623 OSD ypos limited in 1080P?
Hi Chris, You can add reference to vertical offset since this can be used to adjust the display area of both top and bottom position to have only a few rows in top and bottom that are not used.Refer...
View ArticleAD5933 impedance measurement without DC offset over the impedance
Dear, we would like to measure an impedance between 100 KOhm and 500 KOhm butit is not allowed to have a DC voltage over it. Is it possible implement a DC less measurement with/without extra external...
View Articleadv7612 configuration for 720p60
Using custom board with adv7612 which gets 720p60 1. How to make sure that adv7612 outputs correct video?Reading HDMI reg 07 gives x85 where DE is not kocked. 2. The laptop which is my HDMI source not...
View ArticleRe: AD8475 introduces too much noise, any suggestions?
Hello Oliver, Perhaps you could try throttling down the AD8475's bandwidth with a cap directly across the ADC differential input (after the 47 ohm resistors). 0.1uF might be a good starting...
View ArticleRe: SS 3.9!!!
Hi Skfir, Thanks, it's a pleasure to help with your applications since you're always so appreciative. Actually I'm quite ordinary. Bob
View ArticleRe: Camera interface to HDMI port
HI Guenter, Well the update is we could see some activity on clock and data lines at HDMI port pins of ADV7513. But there is no video display on LCD TV. We have YUV422 output from camera and want to...
View ArticleHow could I do a pulse count in ADUCM360?
Hi All, Could I do a pulse count in ADUCM360? Thanks.
View ArticleRe: ADV7393 usage
1) Keep 1.8V <= 3.3V as the power rises. If you look at our reference designs you will notice that the 3.3V and 1.8V come up at the same time 2) I am not sure what the exact question you are trying...
View ArticleRe: AD5933 source code
Hello, I tried before with 2 Vpp but no success. Also I measured frequency on the output and it is about 50 kHz, that was one of the my first test that | have proper communication with AD5933. Can you...
View ArticleSensors details in "iMEMS Initial Sensors" demo video
May I know the sensors details/configuration used in the demo video on http://videos.analog.com/video/products/MEMS-sensors/826028436001/iMEMS-Inertial-Sensors/ ? Can I purchase the complete set or I...
View ArticleRe: ADSP21469 DAC code
Hello,Since this is a SHARC-specific question, I moved it to the SHARC community. Hopefully somebody here can assist you.Thanks,Brett
View ArticleRe: Camera interface to HDMI port
HI Guenter, We checked the waveforms, they are attached for your reference. 1. Hsync occurring after every 2.5msec2. Vsync occurring after every 180msec We observed the ADV7513 input clock coming from...
View ArticleRe: ADV7842 : CP VGA detection
Hello Guenter I would like to identify the two reduced blanking mode : 1920x1200@60hz and the 1600x1200@60hz. But this two mode produce the same result for STDI_BL and STDI_LCF and with experience the...
View ArticleRe: LINUX WITH HDMI VIDEO OUTPUT ON ZC702 BOARDS booting stucked
Hi, Lars, Thank you very much for your reply.I build all the files myself. This is my steps:1. check out the u-boot tree form Xilinx.( git clone git://git.xilinx.com/u-boot-xlnx.git) and build the...
View ArticleRe: ADV7842：In using Auto Graphic Mode, Vsync output was stopped at Freerun.
Hi Aimpoint, Is that the only eval platform you've tried it on? Are you saying when the input video is removed-- it stops outputting any syncs at all? Generally it should free-run unless you've...
View ArticleAD8047 Spice Model
Hello, I am trying to use the AD8047 Spice model in AWR Microwave office. When I load the model and place it in a schematic, the pins are not labeled correctly. They 5 pins are numbered 1, 3, 44, 99...
View ArticleRe: LINUX WITH HDMI VIDEO OUTPUT ON ZC702 BOARDS booting stucked
Hi, Lars, When I build the devicetree, I use the command: make zynq-zc702-adv7511.dtbReference is download form...
View Article