Issues with EVAL-AD7294-2SDZ Current Sensor
Hello, I have both, the EVAL-AD7294-2SDZ and the EVAL-AD7294EBZ.I got the EVAL-AD7294-2SDZ because it allows me to interface to the I2C without cutting traces.However, I don't seem to get the Current...
View ArticleClik here to view.
Communication Problems with AD7734
Hello Every body.Im trying since 3 Days to get a AD7734 working. ill describe the Problem and hope some one can help. The AD7734 is connected with an atmega16 from atmel. REFIN(+), BIASHI and BIAS0 to...
View ArticleADF7023 Reed Solomon (RS) Firmware Issue
Hello, I am trying to get the Firmware rom_ram_7023_2_2_RS_AES.dat on a ADF7023 to work. I am facing the following issues: Config: Packet starting at 0x10, TX and RX on different modules (one only RX,...
View ArticleHigh Spec Automotive Gyroscope
HiI am a student looking for some basic information. I need to discuss chassis roll over sensors in my thesis.I have looked at the ADXRS300. Is this a chassis roll over gyro that is currently used by...
View ArticleRe: An error message appeared and said " *** ERROR *** The circuit is too...
Hi Lucav. Thanks for your answer.I understoof perfectly.I really appriciate your support.dona
View ArticleRe: Calibrating AD5933 with Arduino
Hi there, I would don't quite understand solution in relation to code. Would like to run the AD5933 with arduino and please post modified code! Thank again. Jean
View ArticleRe: Calibrating AD5933 with Arduino
i can run the code on the arduno and get temperature, but flag always comes back 0 when it calls runsweep, so I don't think it is accessing the right byte. How do you mask D11-D10?
View ArticleRe: ADL5801 Quiescent Current
Hi,bkamak Thank you for your reply. I'm trying to use the ADL5801 in low consumption mode.In order to examine the maximum current capacity of the DC / DC converter, I want to know the measure of the...
View ArticleClik here to view.
PIXC and EPPI 's RGBFMTEN can be used together ?
Hi,Board with a RGB666 LCD screen.When not in use PIXC, images can be displayed properly .Such a data stream is：MEM(RGB888)->DMA->EPPI-->LCD(RGB666)EPPI and DMA configuration is as follows...
View ArticleRe: ADL5511 DC detector
This is a plot showing the output bandwidth. So the scale on the horizontal axis does not relate to the original carrier frequency. It is telling how fast the device can respond to changes at the...
View ArticleClik here to view.
Re: AD9102: help with /TRIGGER programming
Hi Larry, Thanks for getting back to me. I don't think that works. Changing address 0x5C to 0x0001 just increases the time that the first SRAM sample goes out the DAC. Here is the a waveform with...
View ArticleClik here to view.
Re: AD9102: help with /TRIGGER programming
Hi Larry, I was fortunate enough to get an AD9102 Eval board today and I reproduced the test condition on the eval board.Here's what I did to the board:Changed the JP1 solder jumper to get it's input...
View ArticleRe: AD9102: help with /TRIGGER programming
Hi Tim - I'll look at this in the lab tomorrow with your regval file. Thanks,Larry
View ArticleRe: PVP Convolution Instructions
Hey there,If you go to:C:\Analog Devices\ADSP-BF609_Evaluation_Board-Rel1.1.0\BF609_EZ-Board\Blackfin\Examples\drivers\pvp(providing you have the BF609 support package downloaded)You can find multiple...
View ArticleRe: VAT demo: how to seperate ObjectDetection?
Hello, That OSStart has something to do with uC. I think you can get a solid understanding if you go into file-io.c/vat_demo.c and follow that through (Not in debug mode, just scroll through/read code...
View ArticleADXL375/377 band width request
Hi , I design a sense for motion dectect. I used ADXL375 , so far I got a issue that bandwidth is to small. I would like that could up to 10Khz that I can catch more peak information. I found ADXL377 ....
View ArticleRe: ADM1276
Hello Ren, Thanks for your explanation.What you meant by 20mV/limit?i don't see the attached design guide.Can you send it to me again?The current limit you mentioned here is the peak current/RMS current?
View ArticleClik here to view.
Re: AD7763 SYNC Signal
Hi Jim_Jim, There will be some changes on the datasheet. Below is the recommended /SYNC timing diagram for the AD7763. The AD7763 goes to /SYNC when the MCLK falling edge senses the /SYNC pin...
View ArticleClik here to view.
Re: Register Read/Write Functionality
Hi David, Do you have specific ADI part? I can refer you to the ADI wiki page ( Analog Devices Wiki [Analog Devices Wiki] ). You can search and find software drivers here of some latest ADI parts....
View ArticleRe: How to get output on HDMI with VGA input in ADV7511- EVM.
Hi, thanks for this infomation. From this it says the HPD = No which indicates that Hot Plug Detect is not detected. When this happens the TX will actually stay in a reset condition. This normally...
View Article