Re: Blackfin KOOP not alive anymore?
sorry, the MAC hardware supports is restricted to10M/100M only, please ignore my last reply.
View ArticleRe: A couple of questions for AD9834
You're welcome.I will now close this thread.Should you have any additional concerns, kindly make a new thread for it. Thanks,Sittie
View ArticleRe: ADV7623 OSD Resolutions
Hi Wahida, I revised the exel sheet attached based on your comment.Please check the attached file and let me know if you found a wrong part. Thanks and regards, Ian
View ArticleRe: ADuM3223 issue
Dear RSchnell,I know if driver multiple MOSFET and RDson is different. But if MOSFET receive max current can cover continua current, I think that is Okay. As customer reply information:After the system...
View ArticleRe: ADuM3223 issue
Dear RSchnell,The D6 and D3 function is avoid reverse current.So, I can try to get rid of D6 and D3 to test.If any new question, I will reply you first and please kindly help suggestion me, thanks!!!...
View ArticleRe: AD650 F/V converter not working.
Hello Mary, Thanks for your assistance. I Have attached the screenshot of the schematics . Also the frequency range for my application is 0hz to 1400hz and max Voutis 5V. As per the calculator given...
View ArticleRe: Measure milli volt with ADuC706x
Thanks for fast reply."The absolute voltage doesn't matter as long as you do a differential measurement."Is it mean changes in bias will effect accuracy in single ended mode? I am new to SigDel ADC's....
View ArticleRe: Input Voltage Range of ADA4433-1W.
Hi Jonathan, Thank you very much! Best regards.Tamu
View ArticleRe: Adv7403 auto detect sequence
Hi Matt,thanks for your response.But my question was: There are 4 auto-detect modes selectable in Register 0x00 (input control). What is their difference? Do they allow to detect the presence of a...
View ArticleRe: AD5933 source code
I performed phase_system calculation during calibration for all frequencies and now results are much better- error is less then 4 % (attached file). I did not find this procedure in datasheet, maybe it...
View ArticleCORE 1 Use VAT lab (Random tree classifier) error
I run the Random tree classifier algrithom which is implemented by VAT lab on BF609 platform Core1, I encounter the following problems:A fatal error or exception has occurred. Description: Attempted...
View ArticleRe: Sometimes Eth0 can't recv data when BF609-board powers on
I used to try repeatedly power on/off for dozens of time, the eth in u-boot still works fine (and I suppose it would be OK after the coming Linux too..), could you confirm how do you boot your Linux?...
View ArticleRe: ADV7623 support resolutions with DisplayLink(DL-3100)
Hi Dave, I revised the attached sheet based on your comment.Please check it and let me know if you found anything wrong. Thanks and regards, Ian
View ArticleRe: ADV7623 support resolutions with DisplayLink(DL-3100)
Hi lan, I did not see the attached sheet. Best Regards,Jeyasudha.M
View ArticleRe: ADV7623 support resolutions with DisplayLink(DL-3100)
Hi, Sorry for the typo, I could see the attached one. Also if you know HTOT, VTOT and Frame rate, you also calculate pixel clock and check whether it is supported or not as per the pixel clock limit...
View ArticleRe: Sometimes Eth0 can't recv data when BF609-board powers on
Eth0 in u-boot works OK, but errors may occur when ucLinux boots up. I boot the ucLinux from nor-flash. Or the error can be repeated just by "ifconfig eth0 down" and "ifconfig eth0 up" in ucLinux if...
View ArticleRe: ADV7623 WUXGA setting
Hi Nikkee, ADV7623 doesn't support VID_STD = 0x19. So you can use VID_STD = 0x0a. Best Regards,Jeyasudha.M
View ArticleADV7623 OSD flicker
Hi All, I have found one problem with the OSD menu. When moving between the top 3 options, the menu flickers. I use ADI On Screen Display v0.63 to general code. Can you help to look at this issue?...
View ArticleRe: Jitter in Vsync ,Hsync at the output of ADV7184 videodecoder
Hi sir , Previous forum i typed as crystal but it was crystal oscillator of 28.6363 MHz. In addition to those could you suggest these things also? 1) We want know equivalent industrial grade...
View ArticleRe: ADV7623 OSD flicker
Hi sally, I will check this and update you. Best Regards,Jeyasudha.M
View Article