Re: Accelerometer and output device for high school physics project
Hi Todd, Would this evaluation system work for you? Nitzan
View ArticleRe: AD7780 only one conversation.
Hi, The differential input voltage range of the AD7780 is equivalent to AIN(+) - AIN(-) = ±VREF/gain. Given a VREF=1V & gain=128, the part can allow a differential input of AIN(+) - AIN(-) =...
View ArticleRe: ADAU1761 Output Dynamic Range and Compressor
Hi BrettG Will the information I have provided enough? With dynamic range and compression on the part of how I should do better? Thank you Paul
View ArticleRe: AD719x communication problem
Hi Siyavash, We are working on this. We'll get back to you as soon as possible. Thanks and Best Regards, Chris
View ArticleRe: getting consistent output from ADIS 16375
I am not using the ribbon cable and instead using the jumper wire in first image. They are 17 cm long. How much length would be ideal for powering the device?You are right. Please mark the other...
View ArticleRe: getting consistent output from ADIS 16375
I understand where you are coming from and these pictures do offer some insights, but there is no substitute for knowing what is going on at the signal level. The "flying lead" approach has worked for...
View ArticleRe: Fast AGC
Here is a dump of the first 0x180 addresses: 0000: 00 00 AC AD 4C 22 00 000008: 00 17 01 CE 00 01 2D 000010: C8 00 0C 00 19 08 00 180018: 00 00 00 00 16 00 58 0C0020: 00 0A 4B FF 02 02 60 030028: 00 00...
View ArticleRe: getting consistent output from ADIS 16375
Just saw your latest reply. Unfortunately, it isn't that simple. Source impedance, load capacitance and signal patterns all play a role. The bottom line question is, is VDD solid, at the ADIS16375...
View ArticleRe: Our power-up sequence for ADV7611
Hello, Yes.Reset is held low while the all supplies are powered up and we have confirmed the reset pulse width.(spec = min 5mS) Thank you. Sincerely yours,Kou
View ArticleRe: ADIS16480 EKF
Hello Gastone,To be honest, this is not the right forum for managing this type of request. While I am not sure that this would qualify as a condition for return under ADI's warranty, I want to help...
View ArticleRe: getting consistent output from ADIS 16375
Thank you for the explanation. I will probe Vdd and current at startup and give you an update
View ArticleRe: ADIS16480 EKF
By the way, I am sorry that my response has been delayed. This is the end of our quarter and we are releasing a new product, which requires an above normal level of attention to documentation projects....
View ArticleSigmaStudio on Windows 8
Hi Please advise when Windows 8 is supported by SigmaStudio since Windwos 8 machine is quite popular now in the market? Regards, Satoshi
View ArticleHigh speed ADC evaluation board with differential inputs
Hi, I was looking for a high-speed ADC evaluation board ( >40Msps + at least 12 bit resolution) which accepts differential inputs. I have to capture a sampled and held waveform output from my chip....
View ArticleRMS-DC converter AD8436 single supply questions
Hi, I have studied the datasheet for the AD8436 RMS-DC converter quite a bit, but there are some things I cannot figure out when using it with a single supply. In the example Vcc = +5V, GND = 0V 1. To...
View ArticleRe: ADV7612 EDID on Xbox 360
The board is a new board that is based on the Irrevium board. The Irrevium board works.The new board works with PC and the HPA (hot plug) works also. The XBOX doesn't look normal because it does eight...
View ArticleRe: AD719x communication problem
Hi Siyavash, Can I ask for scope shots of your digital interface lines? Upon power-up a reset should be initiated so as to place the digital interface to a known state. This is done by writing 40...
View ArticleVB ver. 6 source code for software used in the the AD8369 Evaluation Board
I have been working with an idea that utilizes your AD8369. One of the components in this project is a PC, which adjusts the gain of the AD8369, as a response to the intensity of several other acoustic...
View ArticleCalibration of the ADE7758
Hello all, I have been trying to calibrate the ADE7758 for use in reading Vrms, Irms, WT/Hr, VA/Hr, and VAR/Hr. I feel that I have figured out the Vrms and the Irms pretty well and am able to get...
View Article