Labview source for CN0272 +SDP-CB1Z
Today I ordered a CN0272+SDP-B set from Analog. I am planning to use it in 1kHz ultra fast laser system as a fast photodiode for interferometer application. a) Is it possible to get the Labview source...
View ArticleHDMI mode not detected on ADV7512
Hello, I have a HDMI repeater product using the ADV7512 and a ADV7511. I am debugging an issue with a particular STB that we do not play nice with. The video output has a red shade, and is sometimes...
View ArticleClik here to view.
Re: signal comparison
Hello Gennady, The AB in CD out Condition block (under Basic DSP / Logic) serve well as a comparator. In the circuit shown, when the RMS level ("A") exceeds the threshold ("B"), the block...
View ArticleAbout AD9945(A/D Converter)
Hello ! I have puestion abou AD9945.I want to know , The maximum and the minimum of Internal Clock Delay (tID) at clock rate is 35MHz.These do not sppear in a data sheet. Best regards.
View ArticleRe: The example of dsp communicate with the usb device(such as cy7c68013a)
Anyone has the example?
View ArticleADM3053 layout
HiI would like to start to layout design .Could I have information about layout of ADM3053? I checked UG-234 1) 1) Edge Guarding UG-234 layout doesn’t have the edge guarding on VISO side. a)...
View ArticleRe: An error will occur if Enable ETH1 for core1
Hi,A CrossCore-only application works OK and wouldn't occured this error. Perhaps as you say, there are some conflicts with uClinux.
View ArticleRe: how to format the MTD of SPI flash
Thanks for the log, as mentioned earlier I would also need your kernel configuration file to look into this.
View ArticleRe: Considering Vout setting resistor for ADP2384
Hi LucaV,Thank you for the answer.You mean that either Rtop or Rbot affects voltage accuracy, right? Best,Tarzan
View ArticleRe: CN-0282 EDID Firmware Question
GuenterL 1. I looked at the ADV7611-VER2.9 and i don't see any setup for 800x600 resolution 2. Does this mean i have to modify the EDID scrip for each different laptop ? BR,Vu
View ArticleSeveral issues related to your recent anti-spam effort
Hello, Yesterday I noticed that several discussions I have participated in have been moved to a new space called "test/spam" although they are definitely not such. One example of this is at,...
View ArticleRe: CN-0282 EDID Firmware Question
Hi Vu, With regards to your first question:I would suggest you run the script called::6-1e Port A, 720p,1080i Any Color Space In (YCrCb 444 24bit from ADV761x) Through HDMI Out 444 YCrCb...
View ArticleRe: Question about Size of parallel nor flash of bf609
Thank you very much, Aaronwu! In arch/blackfin/lib/board.c, there is: dcplb_add(CONFIG_SYS_FLASH_BASE, PAGE_SIZE_16MB | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID); I...
View ArticleHow to calculate to convert Full/Limited range(ADV7611)
Hello. I have a question about calculating formula to convert full/limited range. According to "Figure 38. CP Data Path Channel A (Y) for HDMI Mode" of UG-180 Rev.B Page.112, it seems that the formula...
View ArticleClump diode in BF537 GPIO
Hello,I have some questions about over range input voltage in BF537 GPIO.(Over range input is meaning that; Exceed absolute maximum ratings input voltage range. (?0.5 V to +3.6 V)) ･Does BF537 have...
View ArticleInput range determination of ADV7611
Hello. "Table 42. Input Ranges for HDMI Modes" of UG-180 Rev.B Page.104 doesn't show the cases of HDMI_COLORSPACE=0b1000, 0b1001 and 0b1010.Or does it use only 3bit of HDMI_COLORSPACE to determine...
View Article