Re: ADIS16209 Accuracy Problems and Assembly issues
Dear Mark, We have witnessed thar the power flag in all of our assembled boards in on, indicating low power. The register SUPPLY_OUT shows 2.503V.Testing voltage right at the power in pads indicates a...
View ArticleClik here to view.
Re: Queries on AD9914 Parallel and Direct Mode
Most of the registers have 32 bit data format. I am not getting how to write 32 bit data using the maximum available 16-bit data bus width in parallel mode in one WR cycle. For example what will be...
View ArticleRe: ADIS16209 Assembly issues
1.yes, this is the first time we have made large scale production with ADIS16209.2. We are equipped to manufacture 100 assemblies, but we had made 10 as first batch. All of those 10 are showing...
View ArticleRe: Reference voltage for dB values
Hello, The 0.775V standard (1mW into 600 ohms) = 0dBm remains the standard for interconnections between professional audio boxes. Inside the boxes and at the circuit board level, impedances...
View ArticleRe: EVAL-ADE7753 Software error
Hi amrnasser Sure! I can help you in verifying your SPI code. Do you have one already? Or do you have any questions for me prior to writing code? Also, if you can let me know in which step of...
View ArticleRe: How to communicate with ADE7754 to make an energy meter with PIC18F2520
Hi MARS I am not sure that I am understanding your issue correctly. From what I can gather, I assume that you need a rounded value for PF which just says 0,1 or 0.5 based on whichever is closer and not...
View ArticleRe: ADIS16209 Assembly issues
Thank you! You might also want to try to measure the PROD_ID register, which is located at address 0x4A and contains 0x3F51. That will give you another simple way to verify that the internal processor...
View ArticleRe: EVAL-ADIS Software Does NOT Run on Win 7 64bit
One more question: are you experiencing this with an ADIS16209/PCBZ connected to J1 (pins 1-12) or only when you wire J1 to connect to your remote board? If it is with your remote board, you might...
View ArticleI have some troubles when I use CM408 and would somebody do me a favor ?
Hello ! I have some troubles when I use CM408 and would somebody do me a favor ?@Kelven.Mo 1,The SYS_FAULT pin will indicate fault(output low) when power on or after manual reset(by pulling down...
View ArticleRe: ADIS16209 Assembly issues
Hi Mark,Thanks for your responses.Question: if we are getting data, and not only that, it makes sense, but it is not within specs accuracy.Do we still assume internal processor might not have...
View ArticleRe: ADIS16209 Assembly issues
Dear Mark.Is there a way that we can talk?I feel we will be able to convey much more information to each other this way and we are running out of time! Thanks
View ArticleClik here to view.
ADV8005 4k2k(4096x2160)/30Hz output
Hi, Customer would like to have 4096x2160/30Hz output. I can't find any corresponding register settings. Can you please provide the settings for VSP(for any timing input) and Tx, thanks. The detail...
View ArticleADAU7002 interface to GSM module
HelloI'm working on a project that includes a BGS5 Cinterion GSM module. This module only has a digital audio interface of 16bit 8kHz, which results in a bitclock of 256kHz and a LRclock of 8kHz,...
View ArticleADE7880 Reverse wiring of phase and neutral
Hello Everyone, I am working with ADE7880 and want to know how to protect the device when phase line is given to neutral and neutral line given to phase. Please...
View ArticleRe: OpenCV library on bf609-ezkit
Hi, I have moved this question to the Linux Distribution for Blackfin community. Please continue the discussion here. Regards,Craig.
View ArticleRe: Power-up/down Sequence Timing in Digital Potentiometers and Analog Switches
Hello dffdff, All Analog devices are tested for PSS issues. The order you describe is know as the golden routine for powering up devices. The switches in your system have no VL pins and are typically...
View ArticleADIsimCLK (question about phase noise plot)
Hi, I have a question about the phase noise plot that is a result of the ADIsimCLK tool.The plot consist out of 5 plot that show the phase noise of individual parts of the loop and one total. Now my...
View ArticleRe: EVAL-ADV7625-SMZ HMDI passthrough
Hi Jesse, Audio extraction can be tested through the serial port commands using software without J15 installed.For source code , It would require an SLA. Please discuss the details with your ADI sales...
View ArticleClik here to view.
Re: WDTH_CAP problem with BF518
Hello,I am testing different configurations of timer6:*pTIMER6_CONFIG = (WDTH_CAP) | (TIN_SEL) | (PULSE_HI) | (IRQ_ENA) | (PERIOD_CNT);and I configured it to use interrupt priority...
View ArticleRe: Re: Problems obtaining output on the BF527 LCD for LCDColorBar example
Hi Ram, I've asked our hardware team for the expected values at TP18 and TP19, we'll get back to you shortly with these. The section of the EZ-Kit manual you reference above is for the Audio Interface,...
View Article