Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

About Digital data output

Hi, I'm using AD9613 with HSC-ADC-EVALCZ board programming with labview. I have questions about digital output. I used 2.4 MHZ ramp wave and 25MHZ clock both are 1.0Vpp. (Figure 1  . labview)(Figure 2....

View Article


Re: ADV7623 scale text

Hi, Here we have verified in our side,but we could able to do TBOX scaling with increased font. Do you have one of our evaluation board? If so,Please verify in your side,before moving to some...

View Article


Re: LT8650S using dual channel different output cyrrent

HelloAdditional query for start-up dropout viltage.Are there any problem on LT8650S model? Please check the attached file. "LT8650S_startup_dropout_voltage.pdf"I've confirm using LTspice below...

View Article

Re: ADV7180: video quality difference between 8bit and 16bit

Hi, The 16-bit is same as the 8-bit except splitting the pixel up into luma and chrome channels with LLC = pixel rate,while 8-bit LLC = 2 x pixel rate. Please refer Page76 in ADV7180 datasheet....

View Article

Re: Hittite HMC-T2220 PLL loss of lock

I have contacted Camille there in China, he is an excellent resource for ADI. he can help you get an RMA for this box and get it to the repair facility. will you please send me a separate email so I...

View Article


Image may be NSFW.
Clik here to view.

Re: Using extension headers on ADALM-PLUTO

4. The Zynq extension header labels match zynq pin labels, so they are reconfigurable, they will be configured by the bootloader and bitstream and you would have to look at those to be sure what they...

View Article

Re: AD9689 Eval

Yes, there is a signal at J3. I probed it, and even increased the level a few dB. No matter what we try, we cannot get LED 5 or 6 to come on. We even tried higher frequencies, 2GHz for ADC and 500MHz...

View Article

Re: lwIP copy tx vs DMA

Yes, the implementation between the Ethernet driver and lwIP.  (nifce_driver.c) for the Blackfin.RX, Ethernet driver buffers are copied.  For example, RX packet is received, then a lwip packet is...

View Article


Re: How to write my own low-level pin interrupt handler (BF70x, CCES 2.7.0)

Thanks, Kader.

View Article


How to capture Channel A and B of AD9208 simultaneously?

Hi all, I have connected the AD9208 with the FPGA board and is capturing channel A nicely. However I haven't managed to get channel B working (I have tried writing the register in ACE). Also I like to...

View Article

Cumulative Error calculation for a voltage reference - ADR435

Hi,  I am using ADR435 as a reference for a 18 Bit ADC(AD7631). The specification demands a detailed calculation of error introduced by the reference. I have done the error analysis in following way....

View Article

Re: ADV7619 RXX_5V backfeed

Just to enhance what Poornima stated.  Each of those pins are ESD rated for 200V CDM which is good enough for assembly however the real world is much harsher so external ESB protection should be...

View Article

Re: ADV7619 RXX_5V backfeed

Hi,  Yes,ESD protection and backdrive protection are important on each and every external signal line.  Please refer HDMI port protection attachment. Thanks,Poornima

View Article


Re: Update the AD9361 reference HDL design to use ILA?

Thank you Michael. Now I see where u-boot is located. However, when I run the build_boot_bin.sh script from Building the Zynq Linux kernel and devicetrees from source [Analog Devices Wiki], last step;...

View Article

Re: Update the AD9361 reference HDL design to use ILA?

Can you try to run the script with absolute paths? $ ./build_boot_bin.sh /home/user/some/newboot/system_top.hdf /home/user/some/newboot/u-boot-zed.elf -Michael

View Article


Image may be NSFW.
Clik here to view.

Re: Power consumption of LTC2620 Vref

Hiroyuki.D   Yes, that is the way to calculate the current on the reference of the LTC2620.   If you are using 8 channels you it will be about 1.2mA 

View Article

Re: can't find the Devicetree.dtb

Thanks for your patient and careful answer. I have the last problem it may be a silly one .It is which filesyetem I should choose when formatting the SD Card? FAT or FAT32?

View Article


Re: adv7619 Brightness Settings

Hi, Have you configured the color controls registers according to reference script default settings? But still you facing the same,Please let us know. Thanks,Poornima

View Article

Re: How to write my own low-level pin interrupt handler (BF70x, CCES 2.7.0)

I'm having some difficulty with the RTL interrupt support. I am following the example in RTL-Level Interrupt Support for SHARC and Blackfin Processors. My code fragment looks like this:adi_result =...

View Article

Re: ZC702 +FMCOMMS3 with Petalinux-2016.2

Hello Michael,  We are transmitting from one ad9361  and receiving from another. So, we1) Removed Y101 crystal from one ad9361 (acting as receiver)2) Tapped the  CLK_OUT pin of other ad9361  (acting as...

View Article
Browsing all 28044 articles
Browse latest View live