Re: Floating point emulation on Blackfin platform
Hi Michael, There are floating point emulation libraries for the Blackfin. We have two variants; a 'fast floating point' library which is higher performance, and a variant that strictly conforms to the...
View ArticleClik here to view.
ADAUxxxx
Are there any plans to tristate the data line during unused time slots in the adau1761 ? Is the non tristated data line common to all ADAU parts in tdm mode?Regards,Fred
View ArticleRe: Standard digital isolator for I2S audio line
Hello Takehisa, I have not looked into the I2S bus before, so I pulled down the standard and had a look. As you point out this standard is written around TTL logic levels. Our first generation...
View ArticleRe: CN0235 software
Is it anyway that I can get your phone info so I can talk to you verbally?
View ArticleClik here to view.
Re: ADP230X inverting configuration
Oscar, all of the ADIsimPower Design tools have the ability to order an EVAL board.Once you have completed the design click on the "Order Blank EVAL Board" button. This will send us an email with the...
View ArticleRe: HSpice file of ADM2582/2587
Hi Varindra, I have attached IBIS models for the ADM2582E and ADM2587E. We don't supply Spice models for these products. Regards,Hein
View ArticleRe: ADP230X inverting configuration
Oscar, yes the PCB PRD1372 is available and can be requested through the tool. the button for requesting a board is in the upper right hand corner of the tool, in a grey box labeled Request Blank...
View ArticleDual-core PVP?
Hello, Is it possible to use two instances of the PVP concurrently on the BF609 - one on core 0 and another on core 1? Thanks.
View ArticleRe: libiio-interface to matlab
Hi, 1) We've been using the libiio together with the IIO scope application using the remote backend on various laptop and desktop computers with different Linux distributions. So there shouldn't be a...
View ArticleBF60x - PVP Tutorial
Hello, Is there a tutorial that shows how to get started with the PVP Programmer Add-in ? Regards, Mario Bergeronon behalf of FinBoard.org
View ArticleClik here to view.
Re: AD9361 56MHz RX bandwidth
Hi dpu, As said in my previous post, IIO-Oscilloscope doesn’t appear to load the Tx FIR filter file (i.e. I cannot toggle the button that enables the TX FIR filter), even if it is designed with...
View ArticleRe: Output offset with AD620
Hi Peter, Thanks for using ADI products on your applications. Where is your input voltage coming from? Can you make sure that it is not floating by ensuring the it is connected to a common ground where...
View ArticleRe: ADL5304 usable range
Hi Peter, I moved your question about the ADL5304 in the RF Community. Someone here should be able to assist you. Best regards,Emman
View ArticleReference input AD5686R
What is refference current,, input range and input Impedance for VRef in if is used as input for externa reference voltage?In addition toconsidering the use ofinternal andexternal referenceconnected...
View ArticleRe: Noise AD9822
I just take the CCD out of the circuit and I still have noise on the digital part, ThanksMajid
View ArticleRe: Re: MAT14 vs. MAT04
Hi AnnaFeB, I have received another question from the customer.His question is difference between two graphs of Base-Emitter-On-Voltage vs. Collector Current,There is big difference of two graphs in...
View ArticleRe: ADV7343 - Input Clock Frequency
Shall i control the output pixel clock out signal on the LLC pin of ADV7611, the DR_STR_CLK[1:0], IO, Address 0x14[3:2] register by Medium low (2×) for LLC up to 60 MHz If using the above register...
View ArticleRe: Standard digital isolator for I2S audio line
Hi MSCantrell, Thank you very much for your reply and concerning. At first for your question, target performance is 5~6 Mbps in current design, however it may increase to around 20 Mbps in near future...
View Article