BMS
Hey guys. So I just received my EVAL-CN0235-SDPZ & EVAL-SDP-CB1Z yay! This might be a dumb question but if anybody can describe to me, how to attach the batteries to my EVAL-CN0235-SDPZ. I have the...
View ArticleClik here to view.
Re: ADV7511 LLC issue at higher frequencies
Initially is sounds like you are having a signal integrity issue between the FPGA and the 7511. On out ADV7842-7511 reference board with have no problems running 1080p60 over 3 inches and through a...
View ArticleRe: Retrieve data capture of ADC
Hi, The data is stored in memory starting from the DDR_BASEADDR address. Please take a look over the following discussion: Re: Printing data from adc_capture ? Thanks,Dragos
View ArticleRe: How to connect ADF4351 to Matlab
I haven't tested it. It is old software for the ADF4350 board but the ADF4351 is very similar. See can you find the PID variable in the LabVIEW project. Try changing this from 0xB403 to 0xB40D. (0xB403...
View ArticleRe: AD8145 - Video Input Formats
Hello Siva, The AD8145 is simply a triple differential receiver, so it can work with any format as long as the signal is within its specified BW, input range, etc... The two comparators are generally...
View ArticleRe: ADF4351 output phase control.
In your software settings, Phase Adjust is not enabled. Is that a mistake in the screenshot? That reserved bit enables the sigma-delta modulator (which is needed for Phase Adjust) when FRAC = 0...
View ArticleRe: AD737 circuit
I came to this post because the examples on both the datasheet and applications notes for the AD737 did not work. ScottH is right with his circuit proposal. It provides a negative DC signal on the...
View ArticleRe: How to connect ADF4351 to Matlab
That is the name for the file that I can find "PID variable"
View ArticleRe: How to connect ADF4351 to Matlab
I'm not sure. I don't have LabVIEW anymore! Start in 4350_gw_march_win_mod.vi. PID will be associated with the USB connection block.
View ArticleRe: ADV3201 - Video Cross Point Switch
Hi Siva, I'll send you the files offline through our Sales Engineer.Best regards. --Jonathan
View ArticleClik here to view.
ADE7953 design, help/opinion wanted
Hi! My goal is to do a simple energy meter but I'm a computer system's engineer with a little knowledge in electronics. I read the an-1118 application note and i based my design with the figure 5 and...
View ArticleRe: How to convert dBFS scale to dBc
Hello Yoonsun, The figure that Umesh indicated gives a good picture of the relationship between dBc and dBFS. As you have noted, the AD9467 datasheet SFDR specification is in dBFS, and the amplitude of...
View ArticleRe: touchscreen ad7879 on Zynq
Hi, I just pushed https://github.com/analogdevicesinc/linux/commits/xcomm_zynq_gpio_irq_preview With those patches the GPIO IRQs work fine now, both for edge and level triggered IRQs as well as ONESHOT...
View ArticleClik here to view.
ADIS16480 Position tracking Problem
I am trying to track the position of the ADIS16480 sensor by double integrating the accelerometer values. The ADIS16480 is meant to run in inertial frame so that the position is output in reference to...
View ArticleRe: BF609 MSC class example does not build
Hi Craig, Thanks for your reply and for relocating this thread. I am confused though as the USB device MSC is working with the BF526 kit using Crosscore 1.1 tools. This seems inconsistent with the...
View ArticleRe: Interfacing an ADIS16480 to a fit-PC2i-C1600
Since the kernel driver doesn't support all necessary features I have written/am writing a userspace SPI based 'driver'. It uses the libsoc library https://github.com/jackmitch/libsoc which I had to...
View ArticleRe: [ADV7511W] Is sampling frequency of SPDIF updated automatically when we...
Here's the response I got back from the expert. About "0 = use sampling frequency from I2S stream", is this not "I2S stream" but SPDIF? This should probably read 0 = use sampling frequency from audio...
View ArticleRe: ADP5065, two VIN pins
Hi,ADP5065 has two VIN node in order to support higher current flowing and two pins are connected internally. Unfortunately, we don't have separate input paths charger available at this moment. Thanks...
View Article