Clik here to view.
Re: ADV7181C manual input muxing
Hello Dave-san and ADI Support Team. Thank you very much for your support. Takam.
View ArticleRe: AD9361 ADC Clock Configuration using No-OS
Hi Dragos, I had to add this extra function call to get the right RX sample clock (rx_samp_freq?) ad9361_set_rx_sampling_freq(ad9361_phy, 541666);HOWEVER, since then I am having issue with Hardware...
View ArticleRe: VisualAnalog application, calling application by external acquisition...
Hi Juan, I've sent a request to our Software Dev Team to see if they have any example code for interfacing Labview with our VisualAnalog and HSC-ADC-EVALCZ High-Speed ADC evaluation platform. I will...
View ArticleRe: AD-FMCOMMS5 Multi Channel Oscilloscope
Thanks. Initially your fix revealed another hardware problem (apparently unless R350 is depopulated on the FMCOMMS5 board the external LO splitter circuit will not work), but once I removed R350 and...
View ArticleRe: EVAL ADE7878 EBZ- wavesign sampling data acess
Hi augusto.dr I am attaching the waveform sampling related labview codes of the evaluation software here. The entire MCU code is also attached. Software: Labview 2010 & IAR embedded workbench for...
View ArticleRe: AD-FMCOMMS5 Multi Channel Oscilloscope
Sorry - I run into the same problem with the R350 on my early board - but I thought it would be fixed on the boards shipping. So I don't mentioned it. Can you please update you tools using...
View ArticleRe: ADV7842 connected to ADV8003, Test4, Test5, Test8 Pin Conflicts
Guenter,How the ADV7842 behaves if pin C11 TEST8 is pulled up to 3.3V via a 4.7K resistor? Thanks,Tai
View ArticleRe: Question about ADXL362 Real-Time Evaluation System
Hi Nell,Thanks for your help.The issue was solved after writting the hex file of the FTP.I really appreciate your help. By the way, I could not find this FTP site from the homep page.Where can we find...
View ArticleRe: Noise analysis
Hi,If there is a person whno knows ADISIM well, please give me a hand.Please let me know if my question is not clear. Thanks in advance. Best regards,Tarzan
View ArticleRe: Question about ADXL362 Real-Time Evaluation System
Hi Tarzan, Good to know your issue is solved. Refer to the FTP site, you are correct. It is not shown on the ADI website.I will try to make sure all the files on the FTP can be found from ADI website...
View ArticleClik here to view.
Re: Simulink ZC702 AD9364 fmcomms4-ebz
Hi Andrei, It looks like this is where the problem is. I ran "mex -setup" from the Matlab command prompt. However, I get the error:Error using mexNo supported compiler or SDK was found. For options,...
View ArticleRe: zedboard fcomms1-ebz interfacing
helloI am following the discussion..I am working on zedboard with ad-fmcomms1-ebz..My need is to transmit digital data from zedboard through fmc to ad-fmcomms1-ebz and receive the transmitted digital...
View ArticleRe: Changing the Reference Design for the AD-FMCOMMS1-EBZ
hello..I am following the discussion..I too had a same doubt of transmitting signals to DAC of ad-fmcomms1-ebz..Can u help me on how to create a core that generates 8 samples at a time (4 for I and 4...
View ArticleRe: AD8554 - Gain Bandwidth Product doesn't depend on Gain
Hey, thanks a lot for your time! I was stuck with this for quite a while. Problem was, that the noise gain is rarely mentioned anywhere if you do not look for it in particular. So again, thanks a lot...
View ArticleHow to calculate the coefficient of "bass boost" module in ADAU1701?
Hi everyone, I'm using ADAU1701 and would like to control it with the MCU as the host.As I am going to use "bass boost" in my schematic,but I can not figure out the formula to calculate all the...
View ArticleRe: ADV7610 I2C answers xFF for every registers read
Finally had some time to work on this problem and discovered that the SCL and SDA lines were not that nice after all. On the scope, it looks good in zoom out to interpret the I2C message, but in zoom...
View ArticleADAS1000 ECG chip and use of bypass capacitors
The ADAS1000 ECG Front End data sheet suggests using .01uF bypass caps on the analog and digital input supply pins (page 78) but the reference design EVAL-ADAS1000SDZ User Guide schematic shows the...
View ArticleADV212 EIRQFLG doesn't reset
Hello! I'm trying to use ADV21, I make all according to fig.12, page 17 of Programming guide. I have read correct firmware ID=0xff82. Then I try to reset IRQ flags by writing to direct address 0x6...
View ArticleRe: DVI to VGA active RAMDAC using ADV7123
how would i investigate the right part? like i said i dont really know much about designing hardware stuff, so i dont know much about FPGAs or how to program them, i only know software programming (C,...
View ArticleRe: accelerometer for induction motor vibration
Great information, Neil! The following article might be useful as well:http://www.analog.com/library/analogdialogue/archives/48-06/vibration_monitoring.html
View Article