Re: Altera SoC support for AD9361
Hi Kevin, At this moment we don't have a plan to commit our changes on the RocketBoards repository.However, from time to time we are merging our Altera branch with their branch, so maybe it would be...
View ArticleRe: ADE7878: RMS computation
David,Thanks for the reply. We are looking into options for using the waveform samples and doing the RMS calculations with our host processor. One other thought that I had - is there any way to...
View ArticleInternal Voltage Regulator in BF547 600MHz
Hello! The datasheet states that "Use of an internal voltage regulator is not supported on automotive grade and 600 MHz speed grade models." for the BF547. However, the internal regulator works fine in...
View ArticleRe: HMC830
Hello, See the attached gerber files for the HMC830LP6GE evaluation board. Regards,Mark
View ArticleRe: AD8133 Reference Schematics Required
Hi, Jane. We have an available circuit note that is very useful to your application. It is located here - http://www.analog.com/static/imported-files/circuit_notes/CN0275.pdf Instead of AD8133, it uses...
View ArticleRe: AD7998 instable conversion results
Hello here the sch.The Vref is OK. I have a doubt about the fact that some ADC could be damaged because of having some inputs floating during testing and these inputs arrive to the opamp stage and so...
View ArticleRe: Is possible use the ADL 5902 to detect AM signals?
Something is amiss here. Can you post oscilloscope photo of your input signal along with the output signal you are getting from ADL5902?
View ArticleRe: Altera SoC support for AD9361
Is there an easy way to tell when you synchronized with them and from which git branch? Thanks
View ArticleRe: ADuM1251 shows no reaction
Hello Joseph, thanks for your reply and im sorry for my late answer. The fraction of the schematic shown above gives the total amount on components on pin 6 and 7.But i change the ADuM and now it...
View ArticleClik here to view.
ADE7880 - What are limitations or restriction when using rogowski coils
Hello, On my devices that uses ADE7880 3-phase metering IC, it works with CT coil and shunt. Now I need to use rogowski coil with the devices. I noticed on the ADE7880 data sheet that there are some...
View ArticleRe: HDMI 2.0, 600MHZ HDCP 2.2 Transceiver
Hello, We do not currently have a product for 6Ghz HDMI and/or HDCP 2.2. We can't discuss parts in development on the forum. Dave
View ArticleRe: ADV7619 pink lines after switching from unsupported to supported resolution
The ADV7511 is rated only to TMDS clock of 225MHz. 1920x1080@120 would require 297MHz. The 7619-7511 eval board was never designed to run at that rate. The 7619 will handle 3G. I'd check the LLC...
View ArticleRe: ADV7403 and 675i composite input?
Hello Josh, The many other formats are of the un-modulated kind that are video and synchs. The Decoder can't decode anything but the standard NTSC and PAL variants in the data sheet. Dave
View ArticleRe: CVBS IN and HDMI Out (ADV7180 + ADV7513)
Hello, Please open a new thread for new questions. P0 is bit 0--- the LSB. There is a list of input formats in the ADV7513 data sheet that describes how to use that bus to connect. You should be able...
View ArticleRe: HMC928LP5E phase shifter solder implementation question
Adequate grounding is essential for good thermal transfer (read long term reliability) as well as for proper operation at higher frequencies.
View ArticleHMC835 HMC1034 HMC988
Hello, Could you please tell me the differances between the HMC835 and HMC1034 and why one should be chosen over the other? The data sheets appear to have very similar specs, but the price of the...
View ArticleRe: HMC928LP5E phase shifter solder implementation question
Thank you for the answer. My target frequency is 3.5GHz. Thermal issue is not our concern right now because we only like to have a proof of concept experimental demonstration. Do you think it is worth...
View ArticleRe: no video output from ADV7513
The 7513 unique set up for each embedded sync formats. I've attached a script file for our ADV7842-7511 board that configures various modes of embedded syncs between the 7842 and 7511. It's a good...
View ArticleClik here to view.
Re: ADV7604 Low-bit Noise on VGA (1600x1200@60Hz)
Initially I would guess that some power supply noise is getting coupled into the video source. Or possibly a digital noise signal. Does the problem get worst with heat applied? Overflowing freeze...
View Article