Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

Re: The 2011 release compilation

The error says: fatal error: zlib.h: No such file or directory, zlib is not properly installed, try to install zlib1g and zlib1g-dev on your host.

View Article


ADXRS646 calibration

Dear All. I have an application in which I have to measure the angle between a couple of rotating planar surfaces around a common joint. Just for giving you a picture, imagine you have to open a book...

View Article


How to connect and configure ADV7511 to AD9880

Hello,I am student of electronics and I am working on     convert video from analag domain to HDMI. I used AD9880 as analog to digital converter and I have RGB on parallel interface. This signal I...

View Article

Re: Hi, I am new to this forum, how do I access all the files at one go?

Hi Dragos, thank you! That really helped! Next question which I have is, on this link, https://wiki.analog.com/resources/fpga/xilinx/kc705/adv7511#downloads I am trying out the commands here, but I...

View Article

Re: Restarting SE for ADM1069

Hi Ellery, In normal operations the ADM106x's sequencing state machine would come out at the same state before you halted it. A special procedure can be used to re-start the sequencing engine, please...

View Article


Image may be NSFW.
Clik here to view.

Optimal ADC input resistor for ADAU1701

Hi There, Considering I have an input buffer that I can change the gain, what would be an optimal input resistor value for the ADAU1701 for less possible hiss? Currently the buffer is unity gain and...

View Article

Re: Optimal ADC input resistor for ADAU1701

     Hi Fernando,      The Johnson current noise of the total 20K ohm input resistance (18K external plus 2K internal) at room temp & 20KHz BW, works out to 0.13nA RMS.  This is 118dB below the...

View Article

Is it possible for ADV7612 to enter free-run mode without ever connecting...

Hello!  Is it possible for ADV7612 to enter free-run mode and to produce preprogrammed audio-video signals without ever connecting HDMI source to ADV7612's input?In other words, can ADV7612 work as an...

View Article


BF592 timer interrupt

Dear Friends; I am using the BF592 Ezkit to see how to use a Timer to generate an interrupt. Here is the code I wrote: #include <stdio.h>#include "cdefBF592-A.h"#include "defBF592-A.h"#include...

View Article


The IIC configuration list for the ADV7511 in KC705

I am working in a simple design in XIlinx KC705 EVB to display video through ADV7511. Based on the hardware design of KC705, only 18 bits data bus is connected between FPGA and ADV751, therefore, I try...

View Article

Re: How to transfer an azimuth angle?

Hello Allen, Thank you for your post. Since your environment does not appear to support unconditional magnetometer use, that places more emphasis on the gyroscope and accelerometer performance. I would...

View Article

Re: FLAG registers and DAI

Hi Doug, Pg 514 of ADSP-214xx Hardware reference Manual says that GPIO Flags should be connected to the DPI pins . DAI pins does not include GPIO Flags as its source .Also in Pg.No 928 of the same...

View Article

Re: Simulation model for ADUC7023

I'm afraid we don't have any models for any of the Analog Microcontrollers

View Article


Image may be NSFW.
Clik here to view.

Data sheet schematic ILIM ADP1048 error?

Looking at the data-sheet for the ILIM function pulse by pulse OCP the schematic on the right specifically. How can a voltage develop over the sense resistor in the Fet source lead when it is bypassed...

View Article

Re: ADA4941-1 introduces noise

Hi Marco, Thanks for the schematic. I think your resistors are responsible for the noise that you are seeing. Resistors contribute 4nV/rtHz times the square root of the resistor value in kilo ohms (...

View Article


Image may be NSFW.
Clik here to view.

Gain and VRMS Calibration with ADE7758

Good day to all.  I am using ADE7758 for my energy metering for my final year project. I have some doubts from the datasheet and I hope I can clear my doubts here.  1.I am having some problems...

View Article

Re: SSM2018PZ and SSM2018TPZ Specification Issue ?

Hello Paul, The 'T' version of the SSM2018 does not require an external trimmer circuit to optimize the THD. Please see Figure 30 in the datasheet:...

View Article


Re: ADCMP 572/573 Inputs

Hi, meir. 1. Absolutely yes! ADCMP572/3 can handle the LVPECL and LVDS logic levels. Just be sure that the Vcci = 5.2V.  2. The Input Voltage Range (IVR) in the datasheet determines the input headroom...

View Article

Re: VisualDSP++ Floating License Server

Hi, The Operating Systems detailed in my previous post are those which the Floating License Server tools have been tested on and as such we offer support on. Your customer may have success installing...

View Article

Image may be NSFW.
Clik here to view.

Active low pass filter design with single supply opamp

Hi,I designed active LPF with the analog web based application. Since I would not like to have a negative supply in my design I choose to have only positive supply voltage for op amp, but the problem...

View Article
Browsing all 28044 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>