Re: Buildroot: Unable to build uImage from live sources [Blackfin 527C]
I just finished building from HEAD for bf527-ezkit_defconfig and I get an error..../drivers/usb/musb/blackfin.h:51:3: error: #error "Please use PIO mode in MUSB driver on bf52x chip v0.0 and v0.1" You...
View ArticleRe: S/PDIF + analog audio to I2S
Hi alon.bender, The ADAV801/803 are your best bet for this application. No other parts offer both stereo ADCs and S/PDIF. ADAV801 is SPI controlled and the ADAV803 is I2C control. Regards,-BillJ
View ArticleRe: Feeding DAC with my own Real Samples
Thanks a lot Dragos, Will be eagerly waiting. FArid
View ArticleRe: AD7656 CONVST after reset pulse
Hi Karen,Thank you for your quick response. Regards,yk
View ArticleRe: High Harmonics at ADL5387's IF port
Hi, Donald, Per your testing setup, here are the comments: 1. As for the IIP3 shown in adl5387 datasheet, we usually do the two tones measurement setup. i.e. having two closely spaced sine waves input...
View ArticleRe: need video decoder IC which is industrial grade
Hi Sesha, If you require industrial temp range, then I would suggest using ADV7181D and ADV7611. ADV7441A is not recommended for new designs and it is not supported by our new software architecture....
View ArticleRe: Output Protection Circuit for AD5755 ?
Hi, DerrickH as your information for external protection circuit, do you have any suggestion D1/D2 TVS diode spec or parts?from page 47 of latest data sheet, there is not description much detail.Thank...
View ArticleRe: High speed comparator eval board choices
Hi Ronnie, Apologies for the delayed of response. Before we could recommend parts, I need few more details about your applications: 1. What signal levels will the comparator input see?2. Do you need...
View ArticleHow to use Inter Core Communication on bf609?
Hi, everyone, I am trying to use BF609 Inter core communication. The BF609 cpu core A run uClinux, and I want to run software audio echo cancel module on BF609 cpu core B. I find some info about...
View ArticleRe: document of AD9257-65EBZ
Hello Dougl-san, Thank you for quick reply. The board # is 9257EE01A. Thank you.Best regards,Kou
View Articleneed XML file for EVAL-ADV8003-SMZ-P
Matt,I am also unable to find the XML file needed for AVES3 to work with my EVAL-ADV8003-SMZ-P board. Could you post a link? Thanks
View ArticleRe: need XML file for EVAL-ADV8003-SMZ-P
Due to the complexity of this board, we were thinking it might be more user-friendly to use the SW driver rather than scripts to configure the board. I assume this kit included a remote control. Were...
View ArticleRe: ADV7619 simultaneous operation
Can you provide more details on what you are trying to do? -Matt
View ArticleRe: ADUC7020 eval. board software
Board Type : ADuC7020 Eval. Board Rev A2. QuickStart Plus. I searched installed directory (ADuC7XXXV0.2) and (/Keil/Arm/Boards/ADI/ADuc702x), but I can't find board related source codes.When I power...
View ArticleRe: bf609 eppi2 transmit data
have you completed it? if not ,you can try: change ENUM_EPPI_CTL_DLEN08 to ENUM_EPPI_CTL_DLEN16, Even if your hardware is in 8bit mode. i met the similar.
View ArticleRe: ADV3221 IBIS model
Dear Jonathan Thank you very much for your quick answer. ADV3221 is analog device, so it needs SPICE model to simulate, I think too.But in this case, I would like to check only the transmission...
View ArticleCan I use usb and ucfs in bf609_coreB?
HI, Can I use usb and ucfs in bf609_coreB? When I coreB added ucfs, will lead coreA error.TF card initialization and read-write file failed. I joined the two macros defined in the preprocessing :...
View ArticleRe: demodulation sin o square wave?
You can use a sine wave but it it must have a minimum drive level (see Figure 22). Even when you drive the LO input with a sine wave, that signal gets turned into a square wave inside the AD8333...
View Article