ADAU1761 Linux Device Driver for kernel v3.8
I have a Zedboard and am using the AMP reference design (running Petalinux v2013.10). The kernel version used by Petalinux (and Yocto v1.4) is v3.8.11. The audio chip that comes standard with the...
View ArticleFMCOMMS1 Sync
Hello AD, Can you guys clear this up. It is confusing. In reality there are two clock outs (not shown on the block diagram). To ensure that the delay between the clock out from the AD9548 has exactly...
View ArticleADAU1446 - No I2C Comms
I have an ADAU1446 on a board that was working on the last spin of the board, but on this board spin, none of my boards are able to communicate to SigmaStudio through the USBi dongle. I have done two...
View ArticleRF driver
Hi, I have the ZC706 board with AD-FMCOMMS2-EBZ card attached, and am doing the prototyping as per http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/software/linux/zynq. I am looking...
View ArticleRe: ADAU1446 - No I2C Comms
Hi Tom, Unfortunately your schematic didn't seem to attach properly to the first post. Can you try to post it again? Thanks,Brett
View ArticleRe: ADV3002 EDID reply
Hello, My apologies for the delayed response, I was away during our company wide holiday shutdown. Were you able to resolve or make any progress on the issue during this time? Thank you for sending me...
View ArticleRe: ADAU1446 - No I2C Comms
Attached here...Please ignore the note on the schematic that talks about address 0x68. I am talking to this at 0x70.Also ignore the EP pad. That is there, in case we want to stuff an...
View Articleany CrossCore USB examples out there?
Is there an example for using USB with CrossCore? The system services thingy lets you add USB to the drivers but does not have an example. All the other ones I can find are for VDSP. I'm also a little...
View ArticleRe: ADV7611 Evaluation Board Setup
Hello Harpreet, Did you manage to figure out a solution for your issue? I've been trying to do what you describe using the adv7341 eval board, and while I can get the chip to pass through the...
View ArticleIIO Scope tool
Hi, I have set up the AD9361/Zynq evaluation boards and the IIO Scope is up and running. Now I need to find out how to transmit modulated LTE waveform via this setup. On the IIO Scope, I did not find...
View ArticleADSP21469 EZ-Kit with Sigma Studio - Using and External ADC/DAC
Our company purchased the EZKit for the ADSP21469 and are using Sigma Studio. I got the kit to work with the stock codec (AD1939). However, I want to try using external Codecs or ADC/DAC's and am...
View ArticleRe: ADV7511 and ADV7612 with WUXGA
Do you have EVAL-ADV7612-7511 (HDCP-enabled) or EVAL-ADV7612-7511P (non-HDCP)? -Matt
View ArticleRe: Enable of ADL5330
Hello enash-san, Thank you so much for information. Sincerely yours,Kou
View ArticleRe: Has the bug in the exponential decay block (constant db/sec) been fixed?
Likely the original (linear decay) version of this peak envelope detector may need preserving along with any new one. For example, we have existing products that could function in an...
View ArticleFMCOMMS2 DAC_DMA problems
I am using the latest version of fpgahdl_xilinx and no-OS sources (latest as of Jan 6/14) and running on the zc702 + FMCOMMS2 system. The project was created using version 14.4 tools. To test the...
View ArticleRe: FMCOMMS2 Zedboard no-OS Chipscope ADC signal not as in demo
Hi Herwin, Can you tell me where to get the latest HDL.Any special link ? Best reagards,Dan
View ArticleRe: FMCOMMS2 Zedboard no-OS Chipscope ADC signal not as in demo
The latest version is on github. https://github.com/analogdevicesinc/fpgahdl_xilinx Best regards,Herwin
View ArticleRe: AD532JHZ Replacement
Hi, Nandish. AD632 is pin-to-pin compatible with AD532 but has improved specifications. AD632AHZ and AD632SH are 10-pin Metal Header Package [TO-100] which are the exact package replacements of...
View Article