Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Re: ADE7758 Burden Resistor Value

Dear Dlath, I am calibrating the current channels by following the steps shown in datasheet of ADE7758 page 55. As a result, the channel C is able to get quite an accurate reading compared to the...

View Article


Re: Gyroscopes

Hi Jim, I understand where you are coming from. What type of angle accuracy are you looking for?  Are you also considering accelerometers for pitch/roll tilt and magnetometers for yaw-angle estimates?...

View Article


ADUCRF101 data encryption

Is there any data encryption support in ADuCRF101?Somewhere I noticed something about native (HW) AES 128 data encryption.I can't find any data encription support in radioeng API.(Manchester data...

View Article

Re: AD620 drift

Hi dclmThe typ. zero drift of AD620A is 0.3µV/°C. Gain 100 gives 30µV/°C. Then comes the output drift typ. 5µV/°C.This 35µV/°C is amplified with 12 giving 420µV/°C. Over 40°C it is 17mV. Added to this...

View Article

Re: How to connect a 21369 EZ-KIT to ADZS-USBI2EZB and EVAL-ADUSB2EBZ

Ok, found it: SigmaStudio_for_SHARC_Users_Guide.pdf Daniel

View Article


Re: Some questions of ADV7619, again

Ahh,,,,I got it, sorry.Thank you Dave. kaos

View Article

Re: AD-FMCOMMS1-EBZ relayout issue:PIC firmware programming to a...

Dear Micheal,Can you provide a brand about a usb programmer?To update(no os driver),use a usb programmer conect to XP1(on board).then,how to do?Thanks.

View Article

Re: AD5930 and AD5932 evaluation board software commands

Dear Sir, Sorry for the delayed reply. I tried you suggestion but it is not working. I did the following:-1. I connected the Board with Battey supply.2. I took another supply and connected it to the...

View Article


Re: ADV7391 output drive current tolerance

Hi Eugene,  We do not disclose the transfer function because we only recommend customers to use on of two RSET values, 510 or 4120 Ohms.  Regards, Paul

View Article


How to show ADAU1442 SPDIF receiver status?

Hello. I would like to show ADAU1442 SPDIF receiver status and turn on MPx port LED.How to get info from DSP register (selfboot mode) about  correct decoding of SPDIF signal?Thanks for answer.Adam

View Article

Re: AD620 drift

Hi Kenneth43, I use my load cell between 3kg to 3.8kg basically. I did not get the following "Then the poor gain TC of the AD620A, 50ppm/°C will add a lot more drift. 16mV*50ppm/C is 0.8 µV/C, added to...

View Article

AD8232 Filter Question

Hello Everyone,I'm sorry if this question is repetitive, but I tried to find similar questions on the whole forum and couldn't find anything, so I decided to start a new thread. I was looking up the...

View Article

Re: AD-FMComms2 HDL support for Altera FPGAs

Yes - and in the context of your previous question - we will port the same architecture on an Altera platform when available. I am lost on your second question. You should be able to make a decision...

View Article


Re: AD9467FMC connectivity with Zedboard

No i didn't have done any modification to the board, i just followed the steps as it is in the wiki page . . . even i am using the same EDK 14.4 and other stuff.

View Article

Re: ADXL345 registers X Y freezes

What configuration settings are you using with the ADXL345? It sounds like you have either Auto Sleep Mode or Standby Mode enabled. In the POWER_CTL register make sure bit D4 (AUTO_SLEEP) is cleared...

View Article


Image may be NSFW.
Clik here to view.

Re: I2C slave read issue with ADuC7023

Thanks Alex, That solved the problem.  nsolanki

View Article

Re: ADXL346/ADXL345/ADXL350 I2C broadcast address

As far as I can tell the ADXL345 does not respond to the general call address. This is nothing about responses to the call address in the data sheet.

View Article


Re: AD9467FMC connectivity with Zedboard

i have checked my function generator on oscilloscope which is also fine, i cant understand whats the reason. . . what u will suggest to apply some filter on not ??? or to forget this issue for just...

View Article

Re: Need Help: Data acquisition by ADIS16135 MEMS gyroscope

Please find attached word file containing screenshots for both cases and 2 spreadsheets. Thanks

View Article

Re: Need Help: Data acquisition by ADIS16135 MEMS gyroscope

Interesting. In both cases, the result was very close to +1 deg/sec. Let me see if I can get someone to set this up in our lab and try out. This might take a few days, but we will try to do this...

View Article
Browsing all 28044 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>