Re: AD-FMCOMMS1-EBZ Linux
These are really basic Linux questions - May I recommend to start here: http://wiki.analog.com/resources/tools-software/pointers -Michael
View ArticleRe: Need Help: Data acquisition by ADIS16135 MEMS gyroscope
Thanks Mark!!!Look forward to your results.
View ArticleRe: ADV7842 detected ADV7511 HDMI mode as DVI
Hi Phil, Let me comment on this a bit since I saw my name begin used. If you are using our ADV7842-7511 evaluation board I believe the repeater code reads the AVI infoframe from the 7842 and moves it...
View ArticleTemperature stability of ADG1408/1409
Hi I am planning on using the ADG1408/1408 with the 16-Lead Lead Frame Chip Scale Package format for flipchip bonding to a silicon substrate. However, I notice that the maximum operating temperature of...
View ArticleRe: Amp01 single 9V battery supply ... problems
photo, Do you need an op amp or an instrumentation amp? What's the signal source, impedance,single ended or differrential? etc. Harry
View ArticleRe: ADXL377 Output impedance
Thanks, I just wanted to verify that the output wasn't buffered on the evaluation board. I assume from your reply that it is not.
View ArticleRe: Amp01 single 9V battery supply ... problems
Hi Harry;We do photodetector measurements of absolute spectral responsivity here, from the UV to the IR. All kinds of photodetectors are measured. We use both transimpedance amplifiers( I > V , such...
View ArticleRe: Ad-FMCOMMS1-EBZ and Zedboard with Vivado
Rejeesh,Any chance I can get an early copy of that for Zedboard? I don't care if it doesn't work at this point, I'd just like to study it and learn by poking around.
View ArticleRe: ADV760 Pixel Bus causes radiated emission problems with 1080p60 Input
Depending on your system you may have to tweak the LLC_DLL_PHASE so the data bus matches the LLC clock output. Here's a link that discusses this if you need to do...
View ArticleRe: ADXL377 Output impedance
You can also verify this through the evaluation board's user guide:http://www.analog.com/static/imported-files/user_guides/UG-427.pdf
View ArticleRe: OP275 loading?
Mark, Non-linear distortion is only a problem with big swings in common mode voltage.The input capacitance changes slightly. So if impedances are low, you also don't haveto work. In addition, the...
View ArticleQuestions about AD831
Hello, I am using the AD831 in my design, WITHOUT using the internal amplifier (using the differential current output) and I have a couple questions. 1. The internal gain indicated in the datasheet...
View ArticleRe: RClamp0504P vs. RClamp0524P in ADV7612 reference designs.
I looked into RClamp0504P datasheet and it seems very much different from RClamp0524P.RClamp0504P is designed to protect data lines by clamping them to a fixed reference and it has an input for this...
View ArticleDifferences between AD5535 and AD5535B
I am working on a project which used AD5535ABCZ in an early version, but which I was informed by AD was obsolete now. Comparing the AD5535 and AD5535B datasheets, I noticed that the -5V input had...
View ArticleRe: RClamp0504P vs. RClamp0524P in ADV7612 reference designs.
The RClamp0504P has an internal 5V zener and you have to route the trace to each pin. They had an extra pin so they brought it out so you could lower the clamp voltage if you wanted to. The RClamp0524...
View ArticleRe: Building FMCOMMS2 Reference Design
Build both HDL and Linux from git HEAD - and things will work. -Michael
View ArticleRe: AD-FMCOMMS2-EBZ Reference Design
Hi Dragos, Thanks for the response! I thought it was necessary to generate the netlist files from the Xilinx coregen .xco files as explained at the end of the Reference HDL Design page on the Analog...
View ArticleRe: ADV7181C CVBS color issue
Hi Claudio, 1) Check the input CVBS signal, make sure it has the proper color burst amplitude and the color carrier in the active video are looks good2) Make sure the input CVBS has the 75 Ohm load and...
View ArticleProblem with EVAL-AD2S1200SDZ
Hi, I'm using EVAL-AD2S1200SDZ in my project. I connect al the wires like manual describes (EXC, Exc*, Sin, SinLo, and so on). But when I turn the shaft and read the angle the four less significant...
View Article