Re: some basic questions about AD5933
Hi, This is the same thread posted in dds community last feb 26, 2014. Please refer to this thread: http://ez.analog.com/thread/40411 for the continuation of responses.I will now close and lock this...
View ArticleRe: Bandwidth of AD5293
Hi Nom, There has been a case of double posting for this question. You can see the query answered in this thread. I will now close and lock this thread. Thank you. Regards,Mark
View ArticleRe: AD9228 resetting conditions
Dear Moto-san, The AD9228 Power On Reset circuit (POR) will retrigger when the supply goes below about 1.2V (typical value). This POR threshold depends on process and temperature and on the transient...
View ArticleRe: Query for EVAL-AD2S1210 for SPI access
Hi, Apologies for the delay. We are looking into this. We'll get back to you as soon as possible. Thanks and Best Regards,Chris
View ArticleRe: AD7766 full scale ?
Hi, The AD7766 IN+ and IN- can have absolute input voltage of Vref + 0.1 and can accept differential voltage (IN+ - IN-) maximum of +/-Vref. The output of the AD7766 are in 24-bit twos compliment....
View ArticleRe: CN0326: Isolated Low Power pH Monitor with Temperature Compensation
Hi Gowrishankar, Below are the answers to your inquires. 3. High insulation resistance standoff and shielding will vary depending on the environment where the kit will be used. It is highly...
View ArticleADP1047 Recommended Settings
Hi, I have the following questions. 1.0xFE20 - Voltage loop filter gain0xFE21 - Voltage loop filter zero0xFE22 - Fast voltage loop filter gain0xFE23 - Fast voltage loop filter zero For the above...
View ArticleRe: AD5328 stops converting after some time
Hi dorinc, As said in the LOAD DAC Input(/LDAC) FUNCTION Section in page 18 of the data sheet, the operation of the /LDAC function is like that of an OR logic gate. If you wish to control the DAC...
View ArticleRe: A question about AD9915 (3.5 GHz input clock for PLL Disable mode)
Hi Sercan, We'll check on this. We'll get back unto you. RegardsLouije
View ArticleRe: SSM 2018 control voltage scaling
Hi, I moved your question to the Audio community. Someone here should be able to assist you. Thanks, Kris
View ArticleRe: AD9912 Evaluation Board SysClk Input and USB connection
Hi, 1) You may use 0V DC offset.2) Did you use a Windows XP? The software does not work on higher windows.
View ArticleADX345 read output problem
I'm having problem getting the output from this ADXL345.I'm using a LPC1769.This is part of my code: void adxl345_setDataRate (int rate) { uint8_t registerContents = i2c_read_reg (XL345_ALT_ADDR,...
View ArticleRe: AD5328 stops converting after some time
Would you happen to have some scope shots of the SPI lines during the time the DAC stops converting? Would you also be able to send the exact codes that you used? Thank you.
View ArticleRe: AD7606 MISO Doesn't Work
Hi, Have you followed the datasheet recommendations as to the AD7606 operation? Please check this FAQ and let me know if you have covered the points discussed. If you could, please share your...
View Articledo the AD5421's internal DAC and on chip ADC share the same reference?
do the AD5421's internal DAC and on chip ADC share the same reference?How do you test the loop current precision? (The current loop (ILOOP) fault is asserted when the actual loop current is not...
View ArticleRe: Connection check and filter question AD9834
Hi, I have checked your schematic, it's good -- it should be working.A simple low pass filter will work, but a higher order filter is recommended.Miguel has designed a board with integrated 7th order...
View ArticleRe: AD5725 0V transition discontinuity
Hi finishthepint, Are you using the similar schematic diagram as in Figure 28 of the AD5725 Data Sheet? Would you be able to provide more details (schematics, supplies, references, etc) so we could...
View ArticleRe: 26PCD Series Pressure Sensor, Honeywell with AD623
Hi Krisf, Here you are!, the attached file is the sensor's data sheet of 26PCD.Thanks for your help. yutt_p
View ArticleRe: AD5686RARUZ
Hi Kadir, As long as the Vdd is between 2.7V and 5.5V, I think you have done nothing wrong. Do you have maybe have another AD5686R part that you could check? If so, could you also test those? Regards,Mark
View ArticleRe: working with AD-FMCOMMS1 at low sampling rate
Lars, 1) There is no checkbox in configuration. On second tab (Interconnect Setting for BUSIF) there are: Use register slice on AW channels / AR channels / W channels / R channels?Automatic / Fully...
View Article