Clik here to view.
Re: [AD7747-EBZ] Reading Multiple Evaluation Boards in LabVIEW, Problems with...
Hi Sean! This new DLL certainly seems more promising than the previous! So far, I have noticed that the call to Vendor_Request now returns 1 in the error field using the same parameters that all...
View ArticleRe: Noise gate setting in SSM2166
Hello Eric, Thank you for reply.We informed it to customer. Thanks,TAO
View ArticleRe: ADV7850 HDMI input, need I2S pin output
The part should be outputting the audio data. You are setting the right bit to turn it on. Not sure what else could be wrong.
View ArticleRe: AD-FMCOMMS3-EBZ Schematics (non-Adobe Format)
We provide schematics in pdf format and layouts in standard Gerber format. We do not provide schematics in specific tool formats.
View ArticleRe: AD9361 RX and TX ports S-Paramater
I do not expect to see an impact on IIP3. However, balun loss will impact noise figure dB for dB.Ideally you should use different impedance ratio tranformers for different frequency ranges based on...
View ArticleADL5534 for crystal oscillator?
In order to develop a series of compact fixed sinewave RF signal sources between 30MHz and 200 MHz, I would like to use the ADL5534 as the basis for a crystal oscillator with a buffer amplifier....
View ArticleRe: ADL5387 Demodulator RF Input Power dynamic range
Hi, Pal, The minimum RF input power is basically determined by the noise floor. It depends on how noisy the ambience is. The noise figure parameter of ad8342 in the datasheet shows how much SNR...
View ArticleRe: AD8302 Phase error measurement
Dear Mr.Joel Thank you very much for your support.I checked the stand-alone feature.sorry I couldn't show actual data.It is good shape except 80 to 100 deg.I beleve around 90 deg is best shape....
View ArticleClik here to view.
Re: My DSP/DAC Project
Thanks for the heads up Yagami... I have 2 choices I guessKeep on current path and change some register settings and no other changes required...DSP1 OUT:To DSP2CH 0-2 TDM4CH 4- DisabledTo DSP3CH 5-7...
View ArticleRe: ADV7511W Video Troubleshooting
Digging through the various edid info I've collected from 4 TVs. Attempting to send CEA format 4 (720p). Chip reports detected VIC of 4 and sent to rx of 4. I double checked the CEA spec to ensure my...
View ArticleRe: ADE 7880 no-load conditions
Hi Heimo Thanks for sharing that info! As I said earlier, I am currently working on an alternate recommendation and I will get back to you within Wednesday ( 04/02/2014). Let me know if you need to...
View ArticleRe: what's the difference between the application for sigma studio version of...
Hi Deepac,The back channel in my project doesn't work,so I use the debug information instead.As shown below is the code and some debug information in my project. CYCLES_START(oCycleCntStats); /*...
View ArticleReading a configurable setting from external HW into software ?
Hi, I'm building a customized board based on the SHARC 21469 DSP. Is it possible to hook the DAI up to an external pull up resistor with a switch and read the setting of that switch (0 or 1) from the...
View ArticleClik here to view.
Re: Input Biasing of AD8367
Hi, The AD8367's signal input (pin 3) presents a nominal 200 ohm resistance to ground -- thus it expects a ground-referenced input. If you're feeding it from a ground-referenced source (for...
View ArticleRe: ADM811 resistive divide usage
Dear Mr.Ren Thank you very much for prompt and helpful support.I worried about transient current increase or something.but I'll try. Regardsmoto
View ArticlegnICE in SHARC processors
Hello, Anyone has experience using gnICE with SHARC processors? I'd like to know if it's possible to download a dxe file through the gnICE JTAG interface into any SHARC processor, specifically...
View ArticleRe: IC for pi/2 phase shift?
Hi Ahbie, Any updates? Or if you could recommend me a tunable quadrature phase shift circuit? Thanks,Mayank
View ArticleRe: CN0332: Magnetoresistive (MR) Rotational Speed Sensor
Hi can i use this to sense the AC fan motor rotational speed?
View ArticleRe: what's the difference between the application for sigma studio version of...
Additionally,in my normal code of project codes like CYCLES_PRINT(oCycleCntStats); is disable,and not any information will be printed onto console dialog.Regards,Liang
View ArticleTx power monitor damages tx/rx signal
This supposed to be a reply to this tread http://ez.analog.com/message/136724 but on some reason neither my collegs nor myself are able to submit replies to that. We are getting back a error message...
View Article