Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

data size of ADV202 is bigger than expected

When we use ADV202 for JEPG2000 compression with the following code:write_ADV202_indirect(0x00057F08, 0x01000D00) We expect the size of the output image to be around 3328 bytes, but sometimes we get...

View Article


Re: Software Module/Code Example for OSD and SCALING algorithms

Hi Punarva, Thank you Regards,Meir

View Article


Re: AD7993 I2C ACK problem

Hi Jonathan Thank you for the advise. I have tried the following: Connect AS to GND and writing out to address 0x21Connect AS to VDD and writing out to address 0x22 But unfortunately no luck. Apart...

View Article

Re: ADP2300 PFM/PWM mode

Hi kevin, Thank you for the detailed explanation.I see your points, so I will check how it actuallly works on the eval-board. Best regards,Tarzan

View Article

Re: Question about AN-1077

Hi Neil, Thank you for your answer.I understand what you said. Best regards,Tarzan

View Article


Re: ADV7850 HDMI input, need I2S pin output

Dear Guenter, Thanks for your response, and what about the next step to verify the I2S output pin issue?Would you give us some advice to check EVB? Thank you!

View Article

Re: Compare spec between ADA4940 and AD8476

Hi Scott, Thanks for your advice.I'm going to make a signal chain and estimate  the requred system noise level first. Best regards,Tarzan

View Article

Re: AD9361 API drivers for Microblaze

Hi Balaji, Another user asked almost the same thing as you on another thread. Take a look please at what Robin answered (http://ez.analog.com/message/137949#137949). Thanks,Dragos

View Article


Re: About ADP2164

Hi Hong, Do you have some updates on this?Actually,   PVIN pin and VPIN  are connected diffrent voltage rail because of battery system sometime.So let me make sure this issue again.The applied voltage...

View Article


Re: Non-Xilinx / No-OS driver for AD9361

Hi Carsten, We don't have a special driver created for STM32. Our goal is to make it generic, so it will work on many platforms without many changes. I will take a look over your problem and I will...

View Article

Settings of apply external audio to HDMI TX of ADV7623

Dears,     My connections is show in the attatch file. We need to apply external audio from audio input port and insert to HDMI Tx section. Input format is I2S audio.  What are the setting of ADV7623...

View Article

Re: Does CrossCore support TigerSharc ADSP-TS201?

Hi, The CrossCore Embedded Studio tools do not support the TigerSHARC processors - only SHARC and Blackfin. The supported processors are detailed on the CCES Product Page, and in the Release Note...

View Article

Re: data size of ADV202 is bigger than expected

Thanks, DaveD The setup is as followed: (A) Programming the ADV202 for HIPI mode :   1. Write 0x0008h to the PLL_HI register, 0x0004 to the PLL_LO register.   2. Wait for 20us to allow for the PLL to...

View Article


Re: How to calculate the ADC count for gain selection

Yes, as listed in ADC0CON Bit 10 ADC0CODE the "binary" is two's complement coding. And as can be seen from the code provided: Voltage = ADC0DAT * Vref / Gain / (2^N-1) for uni-polar coding and as can...

View Article

Re: ADV7850 HDMI input, need I2S pin output

Dear Guenter, It works, thank you for your great support! Sam

View Article


Re: AD9361 API drivers for Microblaze

Hi Dragos,                       I want to use API drivers of ZC702, which hardware configuration i need to use.For ZC702,i selected XC7Z020-CLG484 FPGA, 1GB DDR3 RAM.any other hardware is required to...

View Article

Re: How to calculate the ADC count for gain selection

Thank you, I will verify it.

View Article


Image may be NSFW.
Clik here to view.

EMI issue of BF537

Hi there,  I would like post a EMI issue from a system with BF537 as main processor.  From the EMI test report, you can see there are some obvious spur over the mask. I want to find the reason where it...

View Article

Re: The max value of delay module

Hi Duke, The maximum delay per 'Delay' module is limited to 1500 samples delay. It is not possible to modify this upper limit. You could cascade multiple such 'Delay' modules and achieve higher delay...

View Article

Re: ADSP-21369 EZ-KIT & FAT16

Hi Luís, I can see that you are using a 4GB SDHC (secure digital high capacity) card. The major compatibility issues between SDHC and SDSC cards are the redefinition of the Card-Specific Data (CSD)...

View Article
Browsing all 28044 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>