Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

Re: The sign of the CMR and more questions

Dear Bob, I am impressed by the speed and quality of your reply. Thank you very much and have a nice weekend! Marian

View Article


Re: Sigma300 (ADAU145x) Q&A

How do we read/find the Silicon Rev of the 1452? When will Rev D be released? Thank you,TomC

View Article


block addressing

I'm referring to this post http://ez.analog.com/message/32330#32330about "grown" blocks addressing and i'm facing the same problem.In detail, i would have the addresses of a grown simple block, in...

View Article

Pulse Shaping of AD9957

Hi,The AD9957's datasheet says that encoding and pulse shaping of symbols must be implemented before the data is presented to the input of the AD9957. What if I ignore the pulse shaping operation?Thanks!

View Article

ADAS3022 input RC Filter issue tracking

Hi, All ADAS3022 input RC Filter issue tracking as below description.1. The Ri = 0805/90.9R on the ADAS3022 EVK, How to decide the Rivalue?2. The IN0+(Reference com point, no connect to ADAS3022 GND)...

View Article


Re: AD7656 reference error question

Hey Rob,We're in the process of rolling the board and have decided that we want to change the reference voltage for the AD7656-1 to accommodate the less than rail-to-rail operation of our opamps. We...

View Article

Re: Huge project to fill up a ADAU1452 and make it do something

Hello Bob: I've been applying this project to a number of 'noisy' sources. I have not yet twiddled too many of the controls, but have noticed that the remaining noise seems to be in the upper...

View Article

Image may be NSFW.
Clik here to view.

Re: ADAU1446 Hilbert transform response

     Hello Tom,      To start with your easiest question:  the Stimulus-Probe tool helps when designing with the standard filters and their cascade / additive combinations.  Find more about this...

View Article


Documentation and size of board for AD8264-EVALZ

 Hello!I am  going to use eval board AD8264-EVALZ for testing our device. Where can I find documentation for board AD8264-EVALZ? Also I find documentation with size of eval board. Thank you.

View Article


Image may be NSFW.
Clik here to view.

DDS: Testing, and Application Signal Chain Building using AD9834

Hi! Kevin, Thanks alot firstly, for helping on my queries. It helps. As informed earlier, I'm possessing two signal generators 33250A (Agilents).However, I want STEPWISE verrification of VPHS o/p swing...

View Article

Re: ADAU1446 Hilbert transform response

Many thanks Bob for your considerations.Unfortunately i cannot "bite the bullet", my DSP is almost full and i have no space to fit the FIR required for HT.I can take some benefit as my upper band is...

View Article

21489 - Low power options?

Hi, I'm wondering about optimizing for power consumption with the SHARC ADSP-2148x in certain situations when DSP is minimal. Are there any special configurations (for example, when just passing audio...

View Article

Re: AD 6655 Operation

Hi, I realized that we did not have a quick start guide posted to the evaluation board page for the AD6655.  Please find it attached and let me know if you still have trouble with operating the AD6655...

View Article


Re: ADF4150HV Ref clock input

Yes, just ensure all the REFin requirements in Table 1 of the datasheet are met.

View Article

Re: ADSP-21369 EZ-KIT & FAT16

Hi Jithul, Just wanted to give a quick update. Regarding the schematic, I'm not using anything extra-ordinary. I'm just using 10k Ohm resistors to pull up the MISO, MOSI, CLK and CS lines from the SD...

View Article


Re: I want Software for use EVAL-ADF411XEBZ1 with LPT Port

Are you seeing any signs of successful communication between the software and the board: If you toggle the Phase Detector Polarity, does the output frequency change?If you change the Muxout options,...

View Article

Re: AnalogDevices.DPG.Interfaces.dll

I'll check to see if we have anything. I'm not sure we do.

View Article


AD-FMCOMMS3 Zynq Time and Frequency domian FFT Differences

I am noticing some differences in the data captures that I am making with the tuner’s (AD9361) ADI software when I take them in the Time domain vs when I take them in Frequency domain.  If I capture...

View Article

Image may be NSFW.
Clik here to view.

Re: Maximum Quality Factor

     Hi Dan,      You can compensate to some extent for the remaining variation of boost with Q, by adding a constant term to the volume control -- this is a small "zero compensation" that adds more...

View Article

Re: ADV7441A with EIA-RS-170

The ADV7441A is quite old and is not recommended for new designs. Have you considered one of our newer products? -Matt

View Article
Browsing all 28044 articles
Browse latest View live