ADL5390
Dear Sir, we are working with vector Multiplier(ADL5390)in our project,it functionsas phase and gain control over the incoming signal.But we are able tocontrol the phase(0 to 360deg) and unable to get...
View ArticleClik here to view.
Re: Problems obtaining output on teh BF527 LCD for LCDColorBar example
Hi David sir, 1) Once again i remember the problem on LCD display pin TP18 and TP19 then 2) I run the program(Char_echo on example )with simulator configuration they get...
View ArticleRe: Video out from AD7341
Hi, For a composite video amplifier with a shutdown feature the ADA4430-1 and theADA4432-1 are good options. Regards, Paul
View ArticleRe: libiio client
I still have the same issue with the latest version of the libiio clientI receive the following error: MATLAB System block 'iio_sys_obj_sim/MATLAB System' error occurred when invoking 'setupImpl'...
View ArticleRe: Re: Expectation when using new(heap_id) and heap_id not present in LDF
Hi Mike, The issue here is that the call to new will throw a bad_alloc exception, which will take you to __lib_prog_term if it hasn't been caught. So what you'd need to do in this case is either wrap...
View ArticleClik here to view.
Re: Re: Re: ADAU1701 and Arduino
Hello Kal, thank you for your help ! Unfortunately it still doesnt work. I would like to show you guys my pin config: So what I am doing all the time is:1. Programm a DSP-Project (.hex) File to the...
View ArticleRe: Trace down cause of load error message "0xYYYY does not exist in the...
Hi Eramirez, I have moved this thread from the Blackfin community to the CrossCore Embedded Studio and Add-Ins community. Please continue the discussion here. The 'Warning: Address ... does not exist...
View ArticleInput Signal Levels for AD9286-500EBZ
Hi all, I'm trying to do SPI control for the AD9286 High speed ADC using an Arduino Uno and Labview. The outputs from the Arduino Uno are 5V for logic high and 0 for Logic Low. I saw while reviewing...
View ArticleAbout ADXL362 Real ODR
Hi, all I meet a problem on ODR setting. I set ODR to 100Hz in FILTER_CTL with 1/4 bandwidth. I set the FIFO size 300(This is AH=1, FIFO_SAMPLE=44) in stream mode . And waiting for WaterMark Interrupt....
View ArticleAD5290 Wiper Temperature Coefficient.
I've looked through the datasheet but I did not see a number for the wiper temperature coefficient. It is noted that "The wiper resistance, RW, is a function of Vdd and temperature. Contrary to the...
View ArticleAD5933 - Impedance vs adaptative MCLK
Hi there I'm using the AD5933 with a custom AFE. I don't use AD5933's frequency sweep feature, I only do single freq measurement.Since I want to measure impedance from 10Hz up to 100kHz, I need to...
View ArticleClik here to view.
Re: ADV7625 EDID problem
Hi Yeguiyou, As you said in the other thread, are you using X2.2.1Exp5 version right? Could you please confirm the software version that you been using? Best Regards,Jeyasudha.M
View ArticleRe: Problems obtaining output on the BF527 LCD for LCDColorBar example
Hi Ram, The best place to start would be the VisualDSP++ Getting Started Guide. This provides an overview of the VisualDSP++ toolchain, a basic tutorial on how to create a session and how to...
View ArticleUsing AD7999 IIO driver
We've hooked up an ad7999 to the I2C bus of a Zynq 7015 (connected via MIO). I added the ad7999 from the staging area to the kernel config, and on the devicetree using the following snippet:...
View Articleparallel assembly question
hi!i'm looking for the fastest way to clear the Content of a Memory area.so[I++]=R0 in a Hardware Loop is possible is there a faster way by using Two Parallel Memory Access Instructions ?? mnop || r1 =...
View ArticleRe: Re: ADUC 7024 eval board I2C slave
I attached the specific file I am trying to work with from the examples provided by analog. please let me know if anything else can help.
View ArticleSYSREF in AD9625-2.5 ADC part
Hi, I am planning to use AD9625-2.5 part in my design. What is the SYSREF in the ADC ? How to select this SYSREF clock ? RegardsSoumya
View ArticleADG1236 PSPICE simulation model problem
Hi, I downloaded simulation model for ADG1236 Analog switch from Analog website, if i try to import it to Cadence PSICE (Version 16.6) am able to generate .lib file but not able to generate .olb file...
View ArticleRe: ADUC 7024 eval board I2C slave
The files you attached are from a keil uvision (realview) example. The keil example is using a file called irq_arm.c where the irq functions are defined. The function there calls void...
View ArticleClik here to view.
Re: EVAL-ADV7280M/81MAEBZ Software problem/I2C Errors
Hello Mr.Ghiorse,1) Do you mind confirming that you are using the EVAL-ADV7280MEBZ evaluation board?2) Are the USB and power cables connected correctly (LED D6 and D7 should both be green)?2) At the...
View Article