Re: ADUC 7024 eval board I2C slave
Thank you very much for ypur help now I will attempt to addapt this to IAR.
View ArticleClik here to view.
Re: port uboot on custom board based on bf548-ezkit(new bee)
luckily, I have successfully load uboot via uart . the problem needed to be solved is to make the board or the uboot support the spi flash(S25FL512S). can anybody give suggestions ,thanks for...
View ArticleRe: AD9361 56MHz RX bandwidth
Hi Ciro, I tried out filter 56MHz_TX_FIRx2_BBPLLx2_ADC_DACx2.ftr. What happened was that application did load the file but the driver did not accepted it as a valid filter. This usually happens when...
View ArticleRe: urjtag: what parameter for initbus when working with BF506-based device...
No, don't have that board around.
View ArticleRe: Re: Debugging for Aduc7060 in Keil
I created ini file for debug. It is working. Thank you, ABuda.
View ArticleRe: Problems obtaining output on the BF527 LCD for LCDColorBar example
Hi David sir, I follow your path but i didn't have BF527 examples,how i can get. I use Windows7 32bit .Is any example available on analog website.
View ArticleRe: ADV7611 : Current consumption of XGA？
Hi DaveD & GuenterL Thank you answers. Best RegardsaimPoint
View ArticleRe: Help with understanding how to configure AD5930
Hi musach,thanks for your fast answer.For the first question: if i calculated with 1kHz/50MHz * 2^24 or with 1kHz/50MHz * (2^24 - 1) the result is mostly equal, but sometimes it give a different...
View ArticleRe: Re: Re: port uboot on custom board based on bf548-ezkit(new bee)
Hi andrewolokita, Thanks for quick response. I did what you told me (sf probe with no parameter , using a new version uboot -2013R1), but the same result... With regard to the signals : RFU...
View ArticleRe: Absolute Max Ratings of Analog Input of ADCs
Hi, Thank you for your reply. I wonder the voltage that could damage the chip/card. Thanks Muhammet
View ArticleRe: parallel assembly question
No, this is not possible. The architecture features one store bus and two load buses. Please refer to the L1 memory section of the Programmer's Reference manual for details (p6-3):...
View ArticleClik here to view.
Re: Absolute Max Ratings of Analog Input of ADCs
Hi again Doug, I investigated the the evaluation boards of these chips. In the schematic of the evaluation board of AD9643 (for ex.http://www.analog.com/static/imported-files/user_guides/UG-293.pdf...
View ArticleRe: Re: How to do a mass erase in boards other than the evaluation boards?
So I suppose my question to you is what code did you download to the part to get it to give you the " Cannot stop ARM device" error?
View ArticleRe: AD9364 Synthesizers
No, there is not. You will need to set the Tx and Rx synthesizers to your desired frequency.
View ArticleRe: AD9361 Resources
I would suggest downloading and reading the two user manuals (available on AD9361 and AD9364) from our website.Downloads require registration.
View ArticleRe: ADV7343 - Input Clock Frequency
UXGA60 has a pixel clock of 162MHz. The ADV7343 is limited to 80 MHz pixel clock, so it will not support UXGA60
View ArticleRe: Re: HDMI configuration(ADV7511)
Looks like a color space issue. Try changing 7511 Main 0x15[3:0] = 0
View ArticleRe: Reg calibration of ADE 7758
Hi Kimaya, For step 4, when I say adjust Wh/LSB I mean for the calculation, which in turn adjusts the parts Wh/LSB using the gain register. The second part is slightly off, the xWG register controls...
View ArticleAD9837, AD8302, AD7357, 10-200kHz Impedance Analyzer
Hello, I am developing an impedance analyzer for a PZT element (capacitive) and I am looking for some advice on the usage of the AD8302. The overview of the system that I am working with is attached...
View Article