Clik here to view.
Re: AD5410, necessary interval between RESET command and available to control...
Hi, Aoki-san! The data sheet did not include a time for the software reset. The part has a minimum time specified of 40us. This is guaranteed by design not production tested so I think that 1ms will be...
View ArticleRe: AD9364 manually initiated calibrations don't converge (quadrature, cp)
"uses the unused receiver" means that Tx Quad cal uses portions of the AD9364 receiver to carry out the calibration. No, there are not additional receivers on AD9364. The issue you are seeing is most...
View ArticleADV8005 DDR2 Loopback issue
I have a ADV8005 evaluation board that I am trying to get the DDR2 loopback test working on. I have tried both the two memory DDR2 loopback test and single memory DDR2 loopback test by performing the...
View ArticleRe: BF60ｘ, driver type for USB0_VBC
Hello Aoki -san. Per JoeT's request, I sent this in response to the private support thread, but additionally I will post it here for all. The attached is the final characterization data from our PTE...
View ArticleAD5360 Eval Board Communication
Hi,I am going to be trying to control the AD5360 eval board using MATLAB and I wanted to know if anyone has any experience using the USB port on the Eval board and Matlab to bypass the gui provided by...
View ArticleRe: ADAU1701 Leaky Mute.
HI Alex: It is possible that the attenuation is not reaching 0 as it should. We can look into this if you send us the setting of your external slew volume control. In the mean time, there are ways to...
View ArticleClik here to view.
Re: ADAU1701 Leaky Mute.
Hello Alex, Likely you're running a signal flow similar to this one: I tried it on a stock Eval-ADAU1701Miniz board and could not duplicate your issue -- a logic Low at the MP2 pin...
View ArticleQuestion about driving AD7176-2
Hi,I have an AFE which uses the AD8221 in-amp.Is it possible to drive the AD7176-2 with this in-amp directly or should I use a buffer stage (i.e. AD8656) to drive the ADC?
View ArticleRe: How to simulate AD9914 in simulink
Hi kazim, We do not have existing library blocks for AD9914. Best RegardsLouijie
View ArticleRe: ADN8831 issue
4 layer PCB gives better thermal relief for the components populated on it. If the PID the components have large temp-coefficients, that might be the case. However, I would check first if the PWM TEC...
View ArticleClik here to view.
Re: ADAU1701 have level data feedback to MCU?
reference modification on my post on 22-Jul-2014 13:00*reference:[1] ADAU1701 datasheet page 22 at first paragraph[2] SPI protocol problems 1701 by Simmartin in JeradL comment
View ArticleRe: ADV8005 to convert 720p60 3D_FP to 1920p30 3D_FP
After speaking with the ADV8005 experts, it seems like the ADV8005 can't scale frame-packed 3D video because of the active space in the video. -Matt
View ArticleRe: Simulink ZC702 AD9364 fmcomms4-ebz
Hi Di, The Simulink libiio files in Simulink libiio [Analog Devices Wiki] did not have the ad9364.cfg file. I copied the ad9361.cfg file and renamed it ad9364.cfg. Is there a ad9364.cfg file? Or a way...
View ArticleRe: Vdd2(Secondary side) question for ADuM1300 CN0064
Hi Miguel. Thank you for your prompt reply!>...... depends on your maximum baud rateDo you have the current data when ADuM1300 drive with the max-baud-rate?Thanks Kaos
View ArticleRe: AD9629 Out-of-Range (OR) digital output
Hi,TonyM Thanks very much for your response, and it really helps. Best regards,sss
View ArticleBF609 uClinux booting fails
Hello, I builded linux kernel and made an uImage for BF609. Then I tried to boot BF609 ezkit using the uImage created newly.Errors are copied and pasted below. I would like to know what the problem...
View ArticleRe: adp2323 emi and snubber design
Thanks LucaV, I think the layout precautions are taken as you mentioned. But i will try to send you some snapshots of the layout. It will be tough to send the complete board layout. Is there an email...
View ArticleRe: AD8367, characteristics under Vs=3.3V
Hi Joel, Thank you for offerring actual data.Could you tell me the matching configuration which you used ?Did you use LC matching ? If so, did you use the components which are described in table 5 of...
View ArticleRe: AD8338, Group Delay vs Gain
Hi ysuzuki, I'll get back on you once I get the data of your desired gains. Thank you for using AD8338 in your application. Best Regards,Jino
View Article