Re: ADF7021 SYNC Word
Really sorry to bring up an old post.however, i am working on ADF7021-N and am not sure how to set the preamble bytes. The data sheet suggests a sequence and the data length, however it does not say...
View ArticleADIS16480: motion along z-axis
To whom it may concern. I used delta v to obtain the vector velocity and then integrated to obtain elevation (motion along z-axys). But it results in a great drift. Even if i filter with an high pass...
View ArticleRe: 7611 12bit 422 DDR Mode
So finally i fixed this problem. Problem was the wrong setting of the LLC. io_set 0x19 0x02 # normal LLC frequency, disable DLL on LLCio_set 0x33 0x00 # bypass DLL on LLC The only part that i still do...
View ArticleRe: high speed clock bus distribution
Hi Donald, The phase noise performance required at each PCBx will help to choose the right clocking products. Do you have a phase noise or jitter target? If you already have an 80MHz oscillator, you...
View ArticleRe: ad-fmcomms1-ebz programming FPGA
hello sirThanks for ur guidance...In test.c file ..under the function void dac_dma_setup(uint32_t sel)...I encountered a set of code for(index = 0; index < tx_count; index ++) { data_i =...
View ArticleRe: How do you connect the EVAL-ADV8005-SMZ to the computer and AVES3?
The EVAL-ADV8005-SMZ is intended to use the serial port and firmware API commands to control the board. The command set can be found here. Advantiv™ EVAL-ADV8005-SMZ Video Evaluation Board
View ArticleRe: ADV7401 I2C bus documentation searched
Hi KLEOTECH,Thank you for your inquiry. You have asked your question in the Help space for learning how to use EngineerZone. For product support please ask your question in the applicable Product...
View ArticleRe: AD9361 - initialization data for specific LTE FDD bands
Hi Constantin, I think that the best approach is to use the no-OS software. The AD9361 driver is generic, so it can be easily used with almost any platform. Using it you will have access to a series of...
View ArticleVideo decoder and Video encoder
Dear supporter,My customer needs a decoder and an encoder with the below listed requirement:No DDRNo pixel repetition, at 576i50 the pixel clock rate should be 13.5Mp/s (couldn't find relevant...
View ArticleRe: Linux OS Booting Fail
Dragos, Yes. The problem is still a problem. Could help? I checked out the git database and worked again.The issue is still an issue two weeks ago. I am now working on another jobs so, if available,...
View ArticleRe: Impedance Measurement by Frequency Sweep
Hi Balaji, 1. Please see the attached excerpt of the code I'm using.2. The approx Zmin value I've used for calculation is 20 ohm, RCAL= 1kohm, RTIA= 148ohm, CTIA=10nF and DAC Output = 600mV.3. The...
View ArticleRe: LO leakage in AD9364 Tx test
Hi Jinoj, We will try to replicate your scenario and we will let you know the result. Regards,Dragos
View ArticleRe: CPLB miss without replacement lwip bf537
Thank you for your question. Help with Using EngineerZone is a place for helping specifically with the functions of working within EngineerZone as a whole, not for Analog Products. Please recreate your...
View ArticleZedBoard + FMCDAQ2
Hi,I would like to know if the acquisition platform FMCDAQ2 can be connected to the FMC slot of the ZedBoard which is LPC.Thank you in advance for your information.
View ArticleRe: ADV7401 I2C bus documentation searched
I am moving this question to the Video community for assistance.
View ArticleRe: AD9364 External LO phase noise
Thank you for your answer. I'm using the Agilent E8257D signal generator as my external LO, which has pretty low phase noise (better than -150dBc/Hz at 5MHz offset at carrier frequencies up to 10GHz)....
View ArticleRe: ADT7320 RDY bit
Hi Lluis i tried 2 parts and the behavior is the same.The sequence you reported works for me too.Actually sometimes, i'm speaking about 10 times in an hour @ 1Hz sampling, step 1) give me 0x80 instead...
View ArticleCPLB miss without replacement lwip bf537
I'm running lwip + vdk project (Analog Devices C++ 5.0 update 10.1) on an ADSP-BF537.The application uses both udp and tcp (several tcp sockets).The problem is that i sometimes raise the condition CPLB...
View ArticleRe: [ADV7611]Can support HDMI 1.4b?
1) Yes, The ADV7611 will support HDMI 1.4b 2) The only differences between 1.4a and 1.4b are "Several minor editorials and clarifications".The only changes between CTS 1.4a and CTS 1.4b is an updated...
View Article