AD9129 DLL Incorrect Phase
Hello, I am using the AD9129 and noticed that my data output is corrupted, e.g. I see lots of spurs when transmitting a modulated waveform. I ran the SED test and that test passes. However, when I read...
View ArticleRe: DAQ2 reference design no longer talks with AD9144
Charly: I think that was a typo. There is no such thing as a ZC106. http://www.xilinx.com/kcu105 http://www.xilinx.com/zc706 http://www.xilinx.com/zc702 That's it. Since the 702 doesn't support JESD,...
View ArticleRe: ADV7614 720p25Hz/30Hz support
First is VERT_FILTER_LOCKED = 1?IS V_LOCKED_RAW = 1?Which port do you have HDMI_PORT_SELECT set to?
View ArticleRe: ADV7182 not able to recognize for short interrupt in input line
Are you clearing the interrupt source after processing them? SD_LOCK_CLR and SD_UNLOCK_CLR
View ArticleRe: adv212 HIPI mode problem
Hello, If your MCLK is 70Mhz and your PLL_LO is 0x84 then you are operating the part far out of spec for JCLK. What speed grade is your part?Dave
View ArticleRe: DAQ2 reference design no longer talks with AD9144
Thanks Robin, Mike, Now that I know that we are talking about the ZC706, what is the Max frequency you are planning on using on the AD9680 input? This will help determine what amplifier would be a best...
View ArticleClik here to view.
Re: ADE5169 support
Hello Hans, Is this still an issue, is the part working with your crystal?If not, are you using our evaluation board or do you have your own custom board? Regards,Dlath
View ArticleRe: Adis16209 test issue
Thank you for letting us know that this information was helpful. We look forward to any new discussions your start!
View ArticleRe: How to fix the error of 'FMComms2 Source' of GNURadio
Maybe try to rebuild libiio then. It may be that the Avahi libs have been updated in your distribution since the last time you compiled libiio, that would explain the error.
View ArticleRe: Challenge in writing to ADIS16448 Registers
I was actually working through some of the signals on the plots and was starting to go down this same conclusion path. We really appreciate you sharing this with us. Congratulations on getting this...
View ArticleRe: AD9889B: no HDCP, leave MDA, MCL unconnected?
Hello, You can use the part if you like, but the part is not recommended for new designs because we cannot support it for new designs. If you have problems, we won't be able to help you with that...
View ArticleRe: Stray voltage on ADV3002 clock and data lines?
Hello, I'm getting an expert on this part to come take a look. Dave
View ArticleRe: AD9889B: no HDCP, leave MDA, MCL unconnected?
Thanks for the answer. You can use the part if you like, but the part is not recommended for new designs because we cannot support it for new designs. If you have problems, we won't be able to help you...
View ArticleAD9361 LO GUI issue
Someone asked by email: We are trying to perform a demo using the FMCOMMS3+Zed board combo. One of the frequencies we need to operate on is 60MHz. The GUI has a limitation for the LO at 70MHz. Can you...
View ArticleRe: AD9361 LO GUI issue
How long would it take - as long as it takes to revise the datasheet. RECEIVERS, GENERALCenter Frequency Min : 70 MHz TRANSMITTERS—GENERALCenter Frequency Min : 70MHz We are not going to allow the...
View ArticleRe: AD9889B: no HDCP, leave MDA, MCL unconnected?
Hello, You can ask-- we will most likely just tell you to use ADV7513. I just want to set expectations that if you start a new design with a NRND part, you probably will not get any help if you have...
View ArticleClik here to view.
Re: Crystal not oscillating-things to check?
Hi, I would like to see your schematic and layout for this part of the circuit. Can you attach screen shots of both for me here? If you prefer, we can continue this in a private discussion. I am also...
View ArticleRe: AD9880 questions
First of all the AD9880 is not recommended for new designs. The replacement part is the ADV7842ADV7842 Design Support Files The customer would have to get their own keys from the HDCP organization....
View ArticleRe: ADV7614 720p25Hz/30Hz support
FIELD0_??? and FIELD1_??? are measurements for interlaced video. Your input is progressive. For progressive use CH!_BL, CH1_LCF, CH1_LCVS & CH!_FCL registers
View Article