Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

Re: ADV7511 Linux Examples running on Xilinx Zynq Board

Hello, Please download the reference design (for the desired board) from github. For example, this is the design for the ZC706:...

View Article


Re: AD8475 using IN 0.8x for aditional low pass filter?

Thanks for that "classification"!!!Und tschüss...

View Article


Re: ADE 7880 no-load conditions

Hi hmani!Thank you for the details. I will try your approach! I do not use the CF-outputs and I am accumulating the energy in my microprocessor. My approach will be as follows:Set VANOLOAD as you...

View Article

About voltage of external regulator at ADAU1452W

Dear support team, I have a question about configuration of power for DVDD at ADAU1452W. Q.Is below configuration of DVDD acceptable?     VDDIO = 3.3V     External PNP transistor input = 1.8V I...

View Article

Re: adxl345EV problem

Hi Lama, I am worry about there is something wrong with your hardware. Please check your I2C connection according to Figure 40, on page 18 of ADXL345 datasheet. Please try to read DEVID firstly to make...

View Article


Image may be NSFW.
Clik here to view.

Query about ADRF6655's Conversion Gain

Hi, thereI brought an EVB of ADRF6655 from your distributor and tested it. Here are two queries that need your help.1, I measured ADRF6655 output signal through spectrum analyzer.But measured...

View Article

Image may be NSFW.
Clik here to view.

Re: Vrms calibration in ADE7758_SPI with Arduino

Hi Dlath, I had disable the LINECYC to read the energy register only and the AWATTHR seem to increase constantly. When the load increases, the AWATTHR register reading increases with every readings. I...

View Article

Re: adv212_firmware_load

Hi Dave, I just changed fpga pins as LVCMOS33 and the Aadv212 started to init succesfully but not stable. One time it inits another time it can not. What i mean is saying is that i m waiting active low...

View Article


Re: Voltage +-50V/100mA driver

Hi Stefan,  Your +/-50V requirement at the output really narrows down the choices for the driver. I would recommend that you take a look at the ADA4700-1 for that purpose. It has a very wide supply...

View Article


Query about AD8370

Hi, there We are using AD8370 VGA in one of our projects at 140MHz.Although,I went through the datasheet i was not able to find the IP3 behaviour and gain step resolution @140MHz at low gain mode and...

View Article

Re: ADL5565 FPBW specifications

Dear Jim, unfortunately I can't accept with you.Looking on your answer we can not trust to the "Test Condition/Column" column at all?6.75 GHz is mentioned on the third page and any engineer immediately...

View Article

Re: FMCOMMS1 : problem with I-data

Hi Alex, I think I found a part of the problem in "ad9122_tune_dci". This function always returns an error the first time the software is launched. But if we launch it again, without turn off the...

View Article

Image may be NSFW.
Clik here to view.

BF524 USB block power

Hello, My board was designed with BF524. BF524 operates as USB device. The circuit is coped below and the same as evaluation B/D.Occasionally, the following situation happens while operating.- VBUS...

View Article


Re: ADV212 in decode mode, 1080i-50Hz

Hi again! Up to this moment, I used only small bitrates below 20MBit/s for the ADV212 encoder. Now, I need to set-up encoder for about 70 MBit/s. However, the encoders generate the total output stream...

View Article

Re: ADC 12/14BIT, >2mS/S, Parallel digital interface

Hi Jonathan,Thanks for response. Regards,Meir

View Article


Re: Efficiency of ADP1607 at 32 uA

Hu Lauren,Thanks for response Regards,Meir

View Article

Re: AD4351 evaluation board: Phase Noise and spurs

Hi, As I can see, if I change the N divider to decrease the PFD frequency, the spurs frequency changes.The ADF4351 only allows to decrease the PFD to 312.5KHz without warning of change the low spur...

View Article


ADG 5412 switch resistance when part not powered

I note there appears to be no statement in the datasheet for the ADG5412 stating what the switch resistance is when the part is not powered.  Some parts do explicitly state that this is high resistance...

View Article

Re: AD5933 source code for AVR problem

You can check original source code for VB. http://www.analog.com/static/imported-files/eval_boards/43927441547743AD5933_OpenMktAppsSoftware_Rev1.0_2007_febuary.zip Regards,Miguel

View Article

Re: Source code for cvapi functions where to find??

Hi,   The API "cvFindHomography" is not supported on Blackfin Image Processing Toolbox.  Regards,Rajesh

View Article
Browsing all 28044 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>