Re: Going from 21469 EZ-KIT Lite to first hardware prototype
Thanks Colin! I have to choose between a very expensive VisualDSP++ licence and an even more expensive Cross Core / uC solution. I would go for the uC solution if I could buy an individual license for...
View ArticleRe: ADV212 in decode mode, 1080i-50Hz
Hi again! Up to this moment, I used only small bitrates below 20MBit/s for the ADV212 encoder.Now, I need to set-up the encoders for about 70 MBit/s. However, the encoders generate the total output...
View ArticleRe: as: unrecognized option '-mnopic'
Hi Evan, what's the version of toolchain you are using? you need the matched version of toolchain for your 2013 u-boot.
View ArticleRe: FMCOMMS1 questions
Hi, The reference design registers two sound cards. One for the HDMI monitor (this is the default sound card) and one for the ADAU1761. When recording or playing back audio you need to make sure that...
View ArticleADAU1701 I2S In - Stereo Out
Hi There, My project consists of ADAU1701 as a slave feeding I2S signal from another IC (HDMI converter - EP94Z3E). The 1701 receives the I2S and outputs it as an analog stereo. Digital IN, Analog OUT....
View ArticleAD9139, saveral questions
Hi, We can see temperature drift data on AD9139 datasheet Rev.0, as Gain Drift = 100ppm/degC, and Reference Voltage Drift = 30 ppm/degC. When we use external reference, does it mean total voltage gain...
View ArticleRe: Problem with AD536AK rms to DC converter
Hi Balint, We are looking into this. I will get back to you soon. Thanks!Kris
View ArticleRe: AD8021 distortion
Hi ldc, We are currently looking into this. I'll get back to you soon. Best regards,Emman
View ArticleRe: IPT BF537 kit
Hi Asif, I'm sorry to inform you that IP Thinking’s IPT-BF537 KIT is not available any more. This platform was originally developed by a former Third Party, IP Thinking, who are no longer active....
View ArticleRe: AD5791 Software
Hi Perryl, Please, find the source code for the AD5791 evaluation board attached to the following thread. http://ez.analog.com/message/51291#51291 I am afraid we do not provide support for the...
View ArticleRe: AD5791 Resistor Matching
Hi smacleod, The AD5791 offers great tempo specs with a R1and RFB match of less than 1ppm. Regards,Estibaliz
View ArticleRe: Eliminating the cable capaciance
Hi Sean, Thanks for the reply From my experience I know that if the cable connecting the sensor output to board is maintained at virtual ground the cable capacitance will not affect the sensor...
View ArticleClik here to view.
Re: What beats are the norm for the ADC ADuC706x
I did make a quick test, just to be sure ;-) My data is well within the typical spec - see below.What you may see in your configuration can be caused by temperature change/drift over time.Also take in...
View ArticleRe: AD9139, saveral questions
Hi Here's my comment.The drift direction of gain might be different from reference.To be safe, it's good to regard +/- 130ppm/C as the total drift.So it's not correct to use +/-65ppm as the total...
View ArticleRe: ADIS16485 driver for Windows
Just checking back in. Are you able to read data that makes sense now or can you offer a specific example that includes device orientation (or motion), along with the register data?
View ArticleRe: AD9361 evaluation board with Xilinx evaluation board...
Jack: The documentation for the FMCOMMS3 at:http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms3-ebz Has a list of supported...
View ArticleClik here to view.
Re: does adv7181 support HDMI-->HVSYNC+RGB(720P,1080P) INPUT?
You misunderstand my question：1：if I use YPbPr, so HD mode for Ypbpr is no problem2：now I use the HSYNC+VSYNC+RGB from other ic output，we use GR mode，7181c said that no valid signal，when we change to...
View ArticleRe: Measuring rolling distance
Thanks, I was thinking there would be some movement that the accelerometer would pick up, but perhaps that distance is too small. Do you know of any good devices that can measure the force, i.e....
View ArticleRe: ADCMP573 latch desable
Hi, Ariel. I just wanted to check on your issue. Have you already resolved it? In case you're still working on this, you may follow the suggestion below. We have noticed that your Hysteresis Control...
View ArticleADA4930-1 Input DC Adjustment from DAC
Dear Sir/Madam,I am planning on using AD8336, ADA4930-1 and AD9681. AD8336 to ADA4930-1 is DC coupled with unipolar signal that has DC offset.The unipolar signal is connected to the non-inverting input...
View Article