ADIS 16480 data output issue
Hi, allNow I do the research of the navigation algorithm using ADIS 16480. I see the output of the 16480 is in navigation frame and the initialization will provides the rotation matrix. I want to...
View ArticleRe: AD9548 DPLL is not locked
Hello Ignat, The frequency lock and phase lock circuits are for monitoring only, and are independent. Were you not able to achieve phase lock by using R0x0600<7>=1? As I said before the lock...
View Articlewhy the adv212 still keep dreq low,when I have sent all code data into adv212?
HI: my 212 setting is described below: hipi,32bit,decode mode,dma0 is attached to the code fifo,dma1 is attached to the pixel fifo; EDMOD0 = 0x00d30000;//code fifo,Burst Transfer...
View ArticleRe: ADAU1701, does the RESET input have hysteresis ?
Hi, Bob, Richard, Thanks for your quick reply !First I was cheking the reset and boot sequence.It seems that there are no problems at the start-up...But I will check the points your advised again.If...
View ArticleClik here to view.
AMI Read data from FIFO
Hello, am an designing high speed spectrometer with ADSP-21489 running at 450MHz. Detector is read by 16b 30MSps ADC with 128 words long bursts. Data from ADC is placed to 128 words long FIFO. FIFO...
View ArticleRe: AD9548 DPLL is not locked
Hello Paul, Reading the AN-1061 attentively, I understood a non-controlling nature of the phase and frequency lock detectors. In my opinion frequency and phase locks are not threshold states such as...
View ArticleRe: a couple of question for AD8260
Hi Kaos, If those parts do not work for you, then you can use the high output current driver of the AD8260. I would recommend that you ground the input pins of the VGA and the buffer. The output...
View ArticleClik here to view.
Re: Refection in REFA of AD9525
pkern: Maybe I find the reason for the reflection. I use HMC910 in previous of AD9525. Each pin of output diff. driver of HMC910 is connected to VCC via a 50 ohm resister, as the picture below shows....
View ArticleRe: ADIS 16480 data output issue
Check out page 30 in the ADIS16480 datasheet, with specific reference to EKF_CFG[3]. Does that meet your need?http://www.analog.com/static/imported-files/data_sheets/ADIS16480.pdf#page=30 If not,...
View ArticleClik here to view.
AD9250-FMC interposer and VC707 integration
Hi, I recently bought AD9250-EBZ and FMC Interposer Card. My aim is to capture the signal through ADC. digitise it and send it to FPGA for filtering. However as a first step, when I try to integrate...
View ArticleAD-FMCOMMS2-EB and ZC702 boot image problem
Hi,we are using ZC702 evaluation board to evaluate AD9361 device, but when i am trying to copy the image file in to SD card i am getting problem.How to copy that image file in to SD card? whether i can...
View ArticleAD9361 Tx port output power
hi, I am working on AD9361 and i am checking the output power of AD9361. I am getting -19 dBm o/p power onyl.i am using TX1A port as output port and i faced problem during changing attenuation.when i...
View ArticleRe: AD9834
Hi! Dear Miguel, In continuation with my earlier inputs, here are few more inputs/comments/discussions around potential automated "Impedance measurement system' which can measure for 100KHz-20/30MHz...
View ArticleInterface with EVAL-ADIS Evaluation System
Hi there, I've been doing the wireless transmission project, in which we hope we can utilize the evaluation board to display and capture data from 16488.The data from the imu including gyros and accls...
View ArticleRe: Interface with EVAL-ADIS Evaluation System
Thanks for the new post! Sounds like things are progressing well. I am not 100% sure that I understand. Are you asking if you can take the data from you receiver and run it through the EVAL-ADIS, so...
View ArticleRe: Interface with EVAL-ADIS Evaluation System
Thanks to your help NevadaMark, it is back to the right track :-)Sorry I should have explained more in details, but yes, you got it. Right now I am sending only gyro's and accl's data, which I think it...
View ArticleRe: In need of help sizing an impact accelerometer
Hi Eaglavin,Did you decide to move forward with the ADXL377? If this is complete, can you mark the post in this chain that was most helpful, with "Correct Answer?" Hopefully you can share some...
View ArticleRe: Interface with EVAL-ADIS Evaluation System
Attached is a schematic I planned, where only 5 pins of the evaluation board being used.
View ArticleRe: Interface with EVAL-ADIS Evaluation System
No worries! This is an interesting idea but the EVAL-ADIS and IMU Evaluation software were not designed to enable customization. We don't presently share the code for the evaluation software but do...
View ArticleRe: Interface with EVAL-ADIS Evaluation System
Thanks for the picture. That helps clarify the approach. Am I correct in that you just want to leverage the display features? That might be a better function for LabVIEW. NevadaMark
View Article