Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

ADIS16480 and Evaluation Board Questions

(Background:) I (or more specifically my team) recently bought the ADIS16480 and the corresponding evaluation board for use with the BeagleBone Black.  This board boots from a microSD card with an...

View Article


Re: AD9959-no signal at SYNC_CLK

Another question is which pin are you trying to view the SYNC_CLK output on?  SYNC_CLK should be on pin 54 which is J13 on the evaluation board.  Pins 1 and 2 (J11 and J12) are SYNC_OUT and SYNC_IN...

View Article


Re: AN-564 ADE7756 Voltage connection

Hi donovanpl123 Yes. I agree that there is some confusion in the illustration of how the voltage sensing is done, in the AN564 app note. In the schematic in Figure 16, L2 line must be tied to AGND. It...

View Article

I need a simple circuit to convert ADum5241 iCoupler isolator I/O to 3.3 volt...

I have used the ADum5241 iCoupler before but you need to run it from 5 volts in order to get it to work properly (can't use 3.3 volts).  The IC is nice and small which is great but interfacing it to...

View Article

Re: AES EBU & SPDIF

Hello Coleman,thanks for your answer.I'll obviously use a transformer to comply to the aes/ebu requirements, but my question was centered more on the aes/ebu - spdif interoperability.The anomaly you...

View Article


Can AD820 "NC" be grounded?

I'm using the AD820 in a loop filter in an RF circuit and I would like to maximize the ground plane area. Can the "NC" pins on the AD820 (SOIC-8) be grounded without ill effects? I am also using the...

View Article

Re: AD7195EBZ USB communication protocol

Thanks for the driver.I could understand, probably, why source code it not distributed, but what about description of communication protocol?

View Article

Image may be NSFW.
Clik here to view.

Re: Allowable Sample rates for the ADAU1701

     Hi Coleman,      Thanks for the clarification.  Since 44.1K extends the lower tolerance range (rather than merely being included in it) the permissible lock range is wider on the low end than I...

View Article


Image may be NSFW.
Clik here to view.

Re: Further questions about DSP Code Programming and Emulator

Hi Craig, Thank you so much for replying to my question about the DSP Programming. I am sorry to reply to your answer late, because I took much time to learn and to compare your answers and the answers...

View Article


Re: AD9760 output constant

Marc_2 wrote: It looks strange that the sum of both output voltages is not 0.96 V but rather close to 0.72 or 0.74 V.Have you checked voltage on all pins, including supply and ground ? Is pin 17 at 1.2...

View Article

Re: Can AD820 "NC" be grounded?

mrln55,   Back in the seventies, "NC" meant that there was no internal connnection, and it's probably truefor 90% of the ICs.  Unfortunately, some newbies would put "NC" on a data sheet when theymeant...

View Article

AD9959 evaluation board control

Hi everyone, I have a question about the AD9959 evaluation board (i.e. the AD9959/PCBZ). In particular, is there a way to externally drive pins P0-P3 of the board in a way that has high input...

View Article

Image may be NSFW.
Clik here to view.

Re: About AD9222 evalution board and the capture board (HSC-ADC-EVALC)

Hi,The AD9222 Eval Brd requires the "HSC-ADC-FIFO5-INTZ" adaptor brd to interface to the HSC-ADC-EVALCZ as noted on our High-Speed ADC Evaluation Brd Info portal at:...

View Article


Re: I need a simple circuit to convert ADum5241 iCoupler isolator I/O to 3.3...

Brian, Thanks, I’ll give it a look. John

View Article

Re: AD9361 latency

Rx and Tx digital signal path latency depends on the configuration of the IC, i.e. interpolation, decimation and the number of taps used in the digital filters. Rx path is comprised of three half band...

View Article


Re: AD7476A analog input over-voltage protection

Hi, I moved this post to the precision converter space in hopes someone here can help. Regards, David

View Article

Re: ADV7511 XILINX EVALUATION BOARDS REFERENCE DESIGN, Handling Interrupts

Dragos,I've attached your original example with my modifications to support external (outside of the AD library) interrupt handling (see #if DISABLE_TO_AVOID_INTERRUPT_CONFLICT notes in transmitter.c)....

View Article


Re: Refection in REFA of AD9525

Hi Jacky, If the HMC 910 is at the destination of the AD9525, then you shouldn't need a termination resistor.  Perhaps your reflections are caused by the pads for the decoupling caps, but I'm still...

View Article

FMCOMMS1-EBZ

Hi, I work with FMCOMMS1-EBZ card with ML605 xilinx board. I tried to run a reference design no-OS driver on this card. But the reference design doesn't work properly. I am using Xilinx-ISE Design...

View Article

Re: AD8302 and AD9834

Would something like this work: http://www.rflambda.com/pdf/phaseshifter/RFPSHT0001W2.pdf Or this: http://micro.apitech.com/pdf/phaseshifters/6709.pdf Joel

View Article
Browsing all 28044 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>