Clik here to view.
Re: Where is the Hardware Trace?
Hi, Can you please describe the behaviour of the Hardware Trace prior to upgrading to 2014R1? I.e. were you able to see a trace with code addresses?
View ArticleClik here to view.
Re: ADE7913 for DC sensor measurement
Hi gaubuali This is what I propose, if you plan to use ADE7913. In fact, you can consider ADE7912 instead if you don't need the third ADC. It is still high-side sensing like you requested. The main...
View ArticleRe: for 1080p30 and 1080p29 adv7611 DE line problem
Hi Matt, We don't have evaluation board for ADV7611. On our custom board, we are successfully capturing the 1080p60, 1080p50, 1080p59, 1080i25. & We are seeing the DE signal is stable and...
View ArticleRe: Document missing on ADV8005 support page
Thanks, I will have a look at it. Kind regards
View ArticleWhere can I get the informations about register and it's address?
Hi, I want to set the hardware gain, attenuation and TX/RX filter, who can tell me where can I get the informations about these registers, and the setting steps of hardware gain and attenuation?...
View ArticleRe: ADN4665 behavior
Hi Edd, where exactly is your line driver positioned?Your hardware setup:SPI Master ----(100m)---> SPI Slave, correct?In my opinion you would need a line driver for SCLK and MOSI next to the SPI...
View ArticleHow to keep the SD of AD-FMCOMMS3 stay up to date?The wiki page is not enough.
Dear all, I have been studying the AD-FMCOMMS3 and Zedboard for more than 2 weeks. I am not familiar with Linux. I tried to update the SD according to...
View ArticleRe: AD5621 Offset Voltage
Hi, there is also a contradiction for the typical offset values @ 25°C: -) Table 2: 0.063 mV-) Figure 30: around 0.8 mV
View Articlejitter be found at AD9880 output Hsync pin
there' an issue reported by Huawei, said there's big jitter be found at the AD9880 output Hsync pin, I described the issue by attached doucment, thanks for your support.
View ArticleLinux OS Booting Fail
Dear Greeting, I try to build Linux OS for FMCOMMS1 on ZC702 platform. I follow Linux with HDMI video output on the ZED and ZC702, ZC706 boards [Analog Devices Wiki] procedure. and finally, I can build...
View ArticleClik here to view.
Re: Linux OS Booting Fail
Hi,Please make sure that both the bitstream and the u-boot were built for the correct target board. - Lars
View ArticleSPI and I2C code examples for ADuC84x?
Where can I find examples for the SPI and I2C interfaces on ADuC84x parts?
View ArticleRe: SPI and I2C code examples for ADuC84x?
We have some basic examples written in assembly coming along with the Evaluation-CD.Sorry nothing in C.But the examples are very small and straight forward and can be easily transferred to C by a SW...
View ArticleADV7182 creates dark line at bottom with NTSC input when ACE is ON
Hello,I am facing an issue with ADV7182 chip in NTSC input format where I can see the dark line at the bottom when ACE feature is ON. This dark line is clearly visible in blue color in free-run mode....
View ArticleADV7604, Time Codes insertion and ADC sampling phase
The adv7604 is working pretty well for HDMI and analog RGB sources and we managed to setup the auto graphics mode for non-supported video formats.However, it sometimes happens that after setting up the...
View ArticleRe: AD5622 I2C Issue
Hi Kevin, Let me apologies for the delay. I found that the AD5622 exhibited an issue as you described time ago.The issue was fixed around 2006, and based on your date code, the parts are from...
View ArticleRe: AD7626 recovering from power-down
Hi Jcolao, thank you for information.For the second question may be I wasn't clear enough: if the wake-up time from the power down condition needs 9.5sec,I suppose the working interval from power-up...
View ArticleRe: Continuous sampling using AD7656 evaluation software
Hi Isaac, Can you take a picture of your set up? Regards,Jonathan
View ArticleADCMP572 CML levels
Hello, Accubeat, one of customers are using the comperator ADCMP572 with CML differential output.The output of the ADCMP572 is connected to the input of the MUX of ON SEMICONDUCTOR - NB6L56 - attached...
View ArticleRe: ADN4665 behavior
Hi Edd, What SPI clock rate are you running at? A block diagram showing the SPI master and slave, the LVDS drivers/receivers and the cable would be helpful, as Reinhard has mentioned, the MISO line...
View Article