Clik here to view.
Re: ad-fmcomms1-ebz programming FPGA
A few things are still unclear to me. I presume you are using the ZED with FMCOMMS1, I don't know to much about your tool version, I would recommend to use Vivado 2013.4. Another misty spot to me, how...
View ArticleRe: BF60ｘ, driver type for USB0_VBC
Hi, I have moved this question from the Processors and DSP community to the ADSP-BF60x community. Please continue the discussion here. Regards,Craig.
View ArticleRe: Building FMCOMMS5 Fails with "No valid object(s) found for...
Hi, The warnings from set_clock_groups are harmless and shouldn't affect the bitstream and can be ignored for now, we'll update and fix the scripts so the warnings wont be generated anymore. The...
View ArticleRe: [ADuM7234(CN0196)] VDDA voltage drop caused by DC voltage input
Basically this is related to the bootstrap supply.Or better to say - switching is expected. See explanation on CN-0196 i.e.: Bootstrapped Gate Drive Circuit The power supplies to the gate drivers for...
View ArticleRe: ad9467 and Linux
Hi, We are currently working on updating the design as well as updating the Linux support. We'll have something to test for you by the end of next week. Apologies for the delay. - Lars
View ArticleClik here to view.
Sigma Stadio export system files
HiI am using Sigma Studio Version 3.11. Build 1. Rev 1356. SigmaStudio generates different functions when using "export system files" compare to what is displayed in the capture window. With the...
View ArticleRe: Libiio example for ad9364
Hi Jan, We'll have an update with newly pre-built files available later this week. I'll let you know. - Lars
View ArticleClik here to view.
Re: ADL5391
Dear Joel, We do have 2 ADL5391, one with R2 open (evaluation board untouched) the other one with R2=56.2 ohm. In both cases we observe reflections from Yp (while Xp seems always matched). Attached...
View ArticleRe: AD9361 - IIO Oscilloscope, "Save Settings"
Hi, Yes, the latest version of the IIO scope no longer has a save button and will save changes automatically after they have been made. We have not seen your issue before, but this doesn't mean it does...
View ArticleRe: ADAS3023: How to release a latch after power up?
Hi Jonathan,Still no solution or work around pointing my issue?Unfortunately I never get an email from an application engineer.I’m thinking about changing the device.RegardsMartin
View ArticleClik here to view.
Re: How to set the filter, gain and read the RSSI
Hi, The rssi and hardware gain are attributes of the phy driver. E.g. see the following example code how to read the rssi.#include #include int main(void) { struct iio_context *ctx =...
View ArticleRe: AD9915 Sync_out generation
Hi,Thanks for this inquiry. You are indeed right. There seems to be a conflict with the information in the datasheet. To clear things, kindly refer to the truth table provided below for the correct bit...
View ArticleRe: AD9680-1000EBZ schematics
Hi Ricky-san, You may look at the design and integration files section of the wiki of the AD9680-1000ebz.EVALUATING THE AD9680/AD9234 ANALOG-TO-DIGITAL CONVERTER [Analog Devices Wiki]Or download from...
View Articlesigfox
Hi, Have you some transceivers supporting this technology called Sigfox ? Do you plan to have one ? Thanks and Regards,
View ArticleRe: AD8367 Gain pin impedance.
Hi,Thank you for your reply.I became clear about this problem, thanks to you.
View ArticleRe: ADN4604 for TFT Monitor
Hi Jarrod, Thank you very much for your quick response It's possible I need work with large distance of cable, 10meters, more or less, althought the distance between the HDMI connector and the ADN4604...
View ArticleRe: About AD5700 Carrier Detect Off Timing
Hi Hara,Apologies I'm not fully clear what is being asked but Figure 5 & Figure 22 in the datasheet may answer your question. RXD will always try to detect the signal that is being received, as I...
View ArticleClik here to view.
Re: ADL5391
Dear Joel, Attached you can see the setup I used in order to determine the reflections (input pure sinusoid with power always 0 dBm from signal generator). - First experiment I made, I used a 50 ohm...
View ArticleRe: AD7294-2
Hi, It looks like you are doing a read from a write-only register (as per Table 9, address 0x00 is for the command register and it is write only). Can you do a read of another register with read or...
View Article