Clik here to view.
Re: adau1761 application problem
Hello Xun Shi, The register addresses are detailed in table 32 in the datasheet. It is located on page 50. Thanks, Dave T
View ArticleSelection help for 2GHz, +26dB gain, differential amplifier
I have a 2GHz, single-ended, +0dBm signal that I need to amplify and turn into two +20dBm signals that are 180 degrees out of phase with each other. Basically a single-ended to differential amplifier...
View ArticleRe: Can we make ADV7626 just pass the AV mute ON to sink without sending...
Hi Leon, It seems there might be difference in the way those evaluation boards handle AVMUTE. In order to control AVMUTE manually, you would need to use the CLEAR_AVMUTE and SET_AVMUTE bits in the...
View ArticleRe: JESD204B (AD9680) on Artix?
Someone will need to point to the exact place, but yes, we have the AD9680 on the AD-FMCDAQ2-EBZ working with the ZC706 (what I use) and a few of the other Xilinx carriers....
View ArticleRe: ADL5385 evaluation board for IQ modulation
Hi, Mo, channel displaying doubled voltage could mean that some channels were terminated with 50-ohm, while the ch in the picture was not. Sorry to keep coming back to this point, because I can't...
View ArticleADAU17xx Data Readback format
Hello All,I have an ADAU17xx part talking to a microcontroller in my application. I'm trying to use the readback tool to read out some rms values from the codec over the I2C bus. I read that the format...
View ArticleRe: ADV7611 custom resolution (2560x720)
Hello, What is the pixel clock for your format? Dave
View ArticleRe: How to program Ext SPI Flash via ADV8005
I haven't had a chance to experiment with this yet, but my understanding is that with the right combination of BLIMP Windows application and evaluation board firmware, users will be able to program the...
View ArticleRe: XSIM Simulation Errors with fmcomms2/zc702 Reference Design
thanks. Which .v file actually defines all these addresses , a file somewhere in \github\hdl ( or in \hdl\tree\master\***) ?
View ArticleRe: Can we make ADV7626 just pass the AV mute ON to sink without sending...
Hi Matt, Yes, I knew the settings to that register 0x4B in TX map. I did set 0x4B in TX map with value 0x80 to unmute video and 0x40 to mute the video, they were working well if adv7626 did not...
View ArticleClik here to view.
Re: ADE7880 - get negative values on xWATTHR, possive values on xVAHR using...
Hi hmani, Thank you for the help. You are right, I can get positive energy after correcting the connection. Thanks again! I want to know: 1. In general under what the condition should I modify the...
View Articlebuild AD9467-FMC project in vivado
hello I am trying to build the AD9467-FMC-EBZ from git-hub in vivado on zedboard, I have successfully built the project in vivado without problems, and exported the hardware to SDK,I copied all the...
View ArticleWhat does SYSFS mean?
Hi guys, I am studying libiio and I saw the word sysfs. I have searched its original form in vain, I mean, it is a shortform and I would like to know its complete name.I think it as a simple question...
View ArticleRe: build AD9467-FMC project in vivado
Hi Khaled, The software is compatible with an earlier version of HDL (AD9467 Native FMC Card / Xilinx Reference Design [Analog Devices Wiki]). Now the Xilinx DMA was replaced by our AXI DMA core, so...
View ArticleClik here to view.
is zed output data timing to ad9364 right
The figure shows the output timing when use zedboard transfer data to fmcomms4.The sdk software use the file no-OS/ad9361/sw at master · analogdevicesinc/no-OS · GitHub but AD9361_InitParam...
View ArticleRe: ad-fmcomms1-ebz programming FPGA
hello sir..I have followed the instructions as told by you in the following link using VIVADO...
View ArticleUsing SD card in BF609 through bare metal programming
I want to use SD card to store data for an image processing algorithm using bare metal programming in BF609 EZ KIT. How can it be done.Support I want to run PEC code that comes with BF609 EZ KIT BSP,...
View Articlewhat is the latency of each PVP block, frame size it can process? operating...
I was going through PVP of BF609 and couldn't get the following information in BF609 Hardware Reference Manual.What is the frame size that each block in PVP process?What is the latency of each block of...
View Article2015080- Anveshan 2014
I m trying to simulate our circuit in ADIsimPE. But i m getting the following error. "*** ERROR *** Cannot find DC operating point - No convergence in pseudo transient analysis" what does this error...
View ArticleClik here to view.
2015080- Anveshan 2014
I m trying to simulate this circuit in ADIsimPE. But i m getting the following error. "*** ERROR *** Cannot find DC operating point - No convergence in pseudo transient analysis" what does this error...
View Article