Quantcast
Channel: EngineerZone: Message List
Browsing all 28044 articles
Browse latest View live

Which one can be better?

Dear colleagues,First of all I want to excuse me about my poor English. I will try to explain myself as well as possible.I want to build a system to mesure the acceleration of the squats (fitness...

View Article


Re: Questions about AD831

Hi Julio, Assuming a 50 Ohm load impedance on the IF connector in Figure 2, then a 1:1 balun would reflect a 50 Ohm differential load impedance across the balun, and then it would be 25 Ohms...

View Article


Re: Changing 1772 filters without sigma studio

Hi JJB, The ADAU1772 has two coefficient memory banks (A and B) for the filters used in the signal flow you create in SigmaStudio. Utilizing this feature along with the Multi-Purpose (MP) pins you...

View Article

Re: AD-FMCJESDADC1-EBZ Board and ML605

How would I get an evaluation license? Rich

View Article

Re: AD-FMCJESDADC1-EBZ Board and ML605

Is it possible to have the ADC output data lines feed directly into the input of an FFT module on the Virtex6 without using any of the fancy JESD204 stuff?  Rich

View Article


Re: AD5933: Can “Settling Time Cycles” register value be 0?

Hi Miguel, Thanks for your message. The frequency is well within 1-100KHz range advertised in the datasheet, how can it be "too low"? How the coherence of sampling or lack thereof can depend on the...

View Article

Re: ADV7625 CSC in front of output

Hello, Sorry.I closeit.Thankyouforananswer. Regards,

View Article

Re: Can I expand the memory size of DPG3 ?

Hello danf. I understand I should use lower carrier frequency. Thank you.ysuzuki

View Article


Re: ADuC7060/61 Flash/EE erasure interrupt

Hi MMA and Alexsandr, I have received tahnk you mail from my customer, said that he well understood Flash/EE by your advices. Regards,Ricky

View Article


Re: About ADP2164

Hi Hong, Thanks for the explanations.Do you think this isuue will be updated on the datasheet as a note?I think some other products such as have the separeted inputpin between PVIN pin and VIN.These...

View Article

Re: AD7689 Analog input question

Hi, Increasing the input voltage beyond the internal 2.5Vref - up to 4V in your case - won’t damage the device and the output code will remain at 0xFFFF, but it may impact the device reliability if...

View Article

Re: HDCP/EDID Controller Error Codes register of ADV7511W.

Hello, Thank you for your reply. I want to know not how to clear the interrupt register but the condition that the error status register 0xC8 [7:4] is cleared.Please tell me the condition that the...

View Article

Re: ADT7461: Confirming how remote temperature is represented

Good to know, thank you.

View Article


Re: National Instruments ADI free software

You said" The ADI Component Evaluator was always offered as a time limited version as indicated every time the application is launched. Now look at your web...

View Article

Re: Pin state in Reset active for ADAU1442 and ADAU1452

With regards to the ADAU1452, the digital I/O pins are high impedance when the \RESET pin is held low. All of the pins have weak internal pulls, the I2C (and \RESET) pins are pulled up and all other...

View Article


Image may be NSFW.
Clik here to view.

Re: working with AD-FMCOMMS1 at low sampling rate

Hi Alex, I thought about a work-around with current 64bit DMA, to make at least 1 channel(I) work correctly by sacrificing independence of the other channel(Q). This will help us a lot until we find a...

View Article

Re: AD-FMComms2 HDL support for Altera FPGAs

The following is the ONLY valid "I/O" direction for the FMC pins on this board.   input   FMC_HPC_LA00_CC;  input   FMC_HPC_LA01_CC;  input   FMC_HPC_LA02;  input   FMC_HPC_LA03;  output  FMC_HPC_LA04;...

View Article


Re: Calcul checksum CRC

Moved this discussion to the SHARC Processors forum. Best regards,Coleman

View Article

ADuC7129 I2C

Thx for help. I need to check this.

View Article

Re: AD-FMComms2 HDL support for Altera FPGAs

Thanks Rejeesh - you have the advantage of having a board in hand while we are still working from docs.  Can I ask you one last thing?  You say "The following is the ONLY valid "I/O" direction for the...

View Article
Browsing all 28044 articles
Browse latest View live